Our favorite hand pump for commuters is the Lezyne Sport Drive HP, and you can read more specifics about why in our full-length guide, written by Dave Yasuda, a writer and tester with over 30 years in the saddle. To sum it up, Lezyne makes pumps with an extendable rubber tube that connects to your tire valve, and that’s the difference between awkward and demoralizing. It’s not the only company that does so, but it is one of the few, and it does it the best. The Sport Drive HP can adapt to any tire valve, has no small fussy parts to lose, and inflates more easily to higher psi levels than anything we tested without floor leverage.
In addition to the Rema patches, put a new tire tube in your kit. The best method for dealing with a flat roadside is to swap out the tube and save the task of patching for later. If you’re not sure what size your tires are, it’s printed on the sidewall of the tire. This inner-tube buying guide has some photos of where to look. What brand is almost irrelevant as many tubes get manufactured in the same place, so whatever your local shop has behind the counter for under $10 will work fine. The only reason to spend more would be to save weight.

These guys are awesome.  After work, I got to my bike to discover my back tire was completely flat.  It had a slow leak, so I was able to pump it up enough to make it to their shop.  I got there 10 minutes before closing and they were able to fit me in.  They replaced my tube and picked all of the glass shards out of my tire.  Awesome customer service and they saved me from having to do this myself in the dark and the cold.


Next to everything else that might go wrong with a bicycle on an extended ride, a flat is a relatively minor issue that can be easily repaired trailside, if the right tools are at hand. If they aren’t, a quick fix can turn into a long walk. Well-prepared riders will perform a tune-up regularly and clean their bikes after every ride. For the less-diligent, a well-stocked repair kit will suffice.
Where to begin?! Long story made somewhat short. I bookmarked this place because I saw their dog Kaya and was sold. Lol. But they had 5 stars too so that helped. Amazing people. Very down-to-earth. Took the bikes down the path to Discovery Park. If you're in-shape and do mild cardio, then it should be an ok ride. I don't do cardio and I found myself trying to sell my soul like 15 times just to get to the top of some hills. Lol. Made it to the Ballard locks and actually got to see a boat pass through! This is the off-season so not much boat traffic. Steve, an engineer we met there, said peak time will start in May. Ate lunch at Ann's in Ballard. Delish shrimp sate! I busted my tire in a pothole and had to make a trip to REI. Which wasn't awful because we wanted to go there anyway. The city was tough to ride in at 5:00pm and we rode the sidewalk most of the way back due to the congestion. Some pedestrians are obvious to you and I almost ran over a few people.. By choice. Lol. Made it back right before they closed at 6:00pm. Easy peasy! Notes: Take some water. Take some pictures. The ride is beautiful so don't rush through. Get there before noon to give yourself some time to cruise.

These guys are awesome.  After work, I got to my bike to discover my back tire was completely flat.  It had a slow leak, so I was able to pump it up enough to make it to their shop.  I got there 10 minutes before closing and they were able to fit me in.  They replaced my tube and picked all of the glass shards out of my tire.  Awesome customer service and they saved me from having to do this myself in the dark and the cold.


Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.

Friction gear systems are a lot simpler to adjust, because the movement of the derailer cable can be modulated as you ride, every time you change the gear- they require less cycle maintenance. Modern index shifting systems are a little more complicated because each ‘click’ must release the exact right amount of cable to allow the derailer to move the correct distance to move the chain from one gear to another. Setting up and adjusting a derailer is not difficult and requires only basic tools, but there is a methodical procedure to follow.

×