We like, and recommend, the Crankbrothers Speedier Lever. If you have to pick only one, go with the Pedro’s, but if you want a backup or have some hard tires to unseat, Crankbrothers is a great choice. It’s only one lever (as opposed to a set of two, like the Pedro’s) and it’s longer, so we didn’t pick it over the Pedro’s for portability reasons. But it’s an excellent tool. It has a wide handle you can grip with your whole hand. Like the Pedro’s, the tip is the right size and shape to prevent slipping and stay in place, and the shape of the handle happens to protect your knuckles if you do slip. Even in situations where I didn’t need it, I liked having it because it made me feel like a pro.
On the other hand, an on-bike repair kit will be a much smarter selection of tools that you are most likely to need. You should figure out the type of screws that are fitted on your bike and the things that are most likely to go wrong on a ride. Address only these things so as not to burden yourself too much with unnecessary stuff. Moreover, there are bike repair kits used on long rides and those used on shorter rides. The longer the ride, the more tools, and spare parts you will have to bring unless you want to have a very long hike back home.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Nice, helpful, friendly. Central location. Good bikes (I had two over two days.) Bikes had a water bottle cage (some places don't do that!) Provided helmets if needed (I didn't) and a one-sided pannier containing a decently strong but not super-heavy cable lock and a patch kit. Only quibbles: 1) The owner helping me with getting my bikes seemed to 'drop me' for too long when someone else walked in. He should have said to them, after asking what they were in for, that 'I'll be with you as soon as I'm finished with this person.' So I had to wait a little longer than desired, but not bad. 2) On my second day, the pannier bag fell off and got lost after I stopped for lunch, which required locking up the bike somewhere, so I took the bag into restaurant and re-attached it using the two velcro straps on the rear rack. I've used many panniers before, thought I did it correctly. But apparently I did not. So I paid $55 (cost) to replace everything in bag and bag. In hindsight, I wished I'd put a bungee around bag straps to really secure it to bike. PROBABLY MY FAULT. 3) Bring a second lock to lock quick-release front wheel, as decently strong but not super-heavy cable lock isn't long enough for both wheels and frame.I had a second cable lock.
Let me go ahead and get the bad stuff out of the way. First of all, this stand is NOT the same level of quality as something you would find in a bicycle shop being used for the shop's repairs. it's quite a bit more flimsy, and the grip likes to rotate if you don't get the bike's center of gravity just right. The tool tray is also made out of a rather cheap plastic that can break easily at the rim. That being said, this stand is perfect for home users and makes mundane tasks like fixing a flat or cleaning the chain much easier. It easily holds my Raleigh Merit 3, and I don't worry about the thing falling even if the grip tilts a bit. The stand significantly shortened the time I needed to change an inner tube on my bicycle, and made me less worried about damaging something on the bike by jury-rigging a stand out of whatever I had lying around.
Mini Pump: This actually goes on the frame of your bike, as it’s a bit too big for most under-seat bags. Coming soon, we’ll have a review from Bill of his very favorite one, but a good pump is a lifesaver. Some people instead carry a CO2 inflator, which is faster and easier to use but does require disposable cartridges, and each time you have a flat, you’ll need at least 2 of those cartridges. There are combined pump/inflator tools that we’ll also talk about soon.
Our favorite hand pump for commuters is the Lezyne Sport Drive HP, and you can read more specifics about why in our full-length guide, written by Dave Yasuda, a writer and tester with over 30 years in the saddle. To sum it up, Lezyne makes pumps with an extendable rubber tube that connects to your tire valve, and that’s the difference between awkward and demoralizing. It’s not the only company that does so, but it is one of the few, and it does it the best. The Sport Drive HP can adapt to any tire valve, has no small fussy parts to lose, and inflates more easily to higher psi levels than anything we tested without floor leverage.
I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
For the budding mechanic: A good pocket sized repair guide. One good option is the “Pocket Guide to Emergency Bicycle Repair” by Ron Cordes and Eric Grove. It’s only 3.5×4.5 inches and a half inch thick. I don’t carry this myself, but for someone who’s new to this whole bike repair business, it’s really helpful to have. A future blog post will cover this book in detail.
Bike Radar gives the Pedro’s levers 4.55 out of five stars and claims they’re the “best out there.” (Can we pause to admire the extra five hundredths of a star the site chose to award it? Very specific.) Aaron Gulley, writing for Outside, states, “I can’t count the number of times I’ve snapped cheap plastic sticks, shredded my hand in the process, stomped around cursing in pain for 10 minutes, and then, insult to injury, been tool-less and unable to get my tire off anyway. That will never happen with Pedro’s.”
Mountain bikers are in different world of repair entirely, one that borders on the comedic absurd. It includes large pumps designed to fill up big, fat tires that squish over things, and a medley of assorted slimes meant to be injected into tubes or tires. In that world, the number of days it takes you to fix your tire and return from the wilderness is a badge of courage—bonus points if you’re bleeding—and we’re guessing that’s not what you’re going for next time you set out for groceries.
A bicycle costs anywhere from $250-$9,000 depending what type and quality of bike you want. A utility bike from a department store might cost $300-$500, but experts caution that it will be quite a bit heavier and not as well constructed as other bikes. For a durable, lightweight bike with front-suspension and decent parts, it’s reasonable to pay $750-$1,200. You might be able to pay slightly less, but expect to need some repairs after several months of heavy use.
Patch kit: Patch kits are easy to use, light and compact, and if you get more than one flat on a ride (it happens more than you’d expect), it can save you when you’ve already used your spare tube. Plus, on a rear wheel, patching a tube can be faster than replacing it, as you can often do this without removing the wheel at all. Another upcoming post is going to show you how to patch a tube.
Every expert I spoke to recommended Pedro’s Tire Levers by name. They have a wide body—a different shape than other models we tested—and that prevents breakage, but more important, the broad, flat surface area of the tip helps it stay locked under your tire. When a lever slips from under the bead of the tire, you can end up repeatedly scraping your knuckles on the spokes of the wheel, which is so annoying. Pedro’s levers are small enough to fit into a saddlebag, are sold widely in bike shops, and even come with a lifetime guarantee. If one breaks, Pedro’s will replace it.
We offer several bicycle repair packages, or individual services in the case that you don’t need a full “tune-up”. Whether it’s a small brake adjustment or a complete bike overhaul, we’re happy to help. Our highly experienced staff is here to answer any questions you may have and will help get you and your bike back on the road as quickly as possible.