Professional mountain biker Rebecca Rusch has been on plenty of long rides and experienced enough mechanical failures to know what makes a fully-stocked repair kit. One of her recent journeys, a 1,200-mile journey through the jungles of Vietnam, Laos and Cambodia along the Ho Chi Minh Trail required the utmost degree of preparedness — “We brought with us a lot of extra bearings, o-rings, stuff that you would never be able to find in Laos and Cambodia. Before I go out on these big adventures, I replace every bearing in my bike, my fork got a total rebuild — everything is in pristine condition,” says Rusch.
Patch kit:   Patch kits are easy to use, light and compact, and if you get more than one flat on a ride (it happens more than you’d expect), it can save you when you’ve already used your spare tube.   Plus, on a rear wheel, patching a tube can be faster than replacing it, as you can often do this without removing the wheel at all.  Another upcoming post is going to show you how to patch a tube.
I own the Lezyne CNC Chain Rod, which I’m a big fan of (yes, I know I’m partial to Lezyne here–they’re a local-to-me, San Luis Obispo company and they sponsored my collegiate team, so I got tons of gear) and it costs right around $30. But the truth is that even the cheapest of chain whips will likely do the job. In fact, I’ve found a dude who knows his stuff and shows you how to make this tool all by yourself. I would even go so far as to say that you probably have enough materials laying about your garage (if not, try your parents’ garage ? ) to put this together without spending anything. Check out the video below:
In addition to the Rema patches, put a new tire tube in your kit. The best method for dealing with a flat roadside is to swap out the tube and save the task of patching for later. If you’re not sure what size your tires are, it’s printed on the sidewall of the tire. This inner-tube buying guide has some photos of where to look. What brand is almost irrelevant as many tubes get manufactured in the same place, so whatever your local shop has behind the counter for under $10 will work fine. The only reason to spend more would be to save weight.
I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
Keychain style flashlight or headlamp, LED type, not incandescent:   The keychain style is tiny and lightweight, the headlamp style is a bit bulkier but easier to use.    You can get these for a couple of bucks or less at the local big box hardware store.  The LED ones are lighter, more durable and last considerably longer.   Very useful if you need to make a repair after dark!  I keep a keychain style one as a backup as I normally have a headlamp in my backpack.
All multi-tools are not created equal, but most with a plethora of features will get plenty of the jobs done. I personally like, and use often, the Lezyne RAP-21 LED tool, which will run you around $30. I like it because not only is it a high quality construction, but it has just about everything you’ll need, plus a sweet mini light. This will give you a chain breaker, spoke wrench, disc brake wedge, and all the most often used Allen keys and drivers. We’re talking a decent number of tools for 1/4 of what they would cost buying them separately.
These folks took me in right away, diagnosed and fixed my stripped handle bar clamps and had me on my way to work in about 15 minutes. Friendly, straightforward, understands the rider's objectives (in my case, how do I get home from work). Not to mention, the fee was reasonable. I have been in many bike repair places in my 6 decades. This is the best.
Mountain bikers are in different world of repair entirely, one that borders on the comedic absurd. It includes large pumps designed to fill up big, fat tires that squish over things, and a medley of assorted slimes meant to be injected into tubes or tires. In that world, the number of days it takes you to fix your tire and return from the wilderness is a badge of courage—bonus points if you’re bleeding—and we’re guessing that’s not what you’re going for next time you set out for groceries.
A wrench that fits the hub nuts:   If your bike has quick release front and rear wheels, you don’t need this, but if you have an internal hub on the back, such as the NuVinci, a wrench that fits is a great idea.  99% of the time, this is a 15mm wrench, but you should check your bike.   A 6 inch adjustable wrench can also work, but it will be heavier, and when using an adjustable wrench, you do need to take more care to not round over the nuts.   A fixed wrench is the best choice.    Some multi-tools have a 15 mm wrench built in, but again, if you have limited hand strength, something with more leverage is a great idea.

A good patch will stick to your tube enough to keep air from leaking out. A great patch will act like a second skin and actually strengthen the tube where it’s applied, flexing and stretching with the tire. After 36 hours of testing, our official endorsement goes to the Rema TT 02 Touring Repair Kit. Its patches do everything other patches do, just better. The edge of the patch is also ruffled, which provides more edge surface area to bond—that’s a good thing.


The best type of bike for exercise depends what level of rider you are and whether you would rather ride on trails or on the road. There is a type of road bike that is called a “Fitness Bike,” and features a lightweight frame and narrow tires, but do not have a drop handlebar. This may be the best type of bike for someone who intends to ride regularly and strenuously on the roads. If you plan to do a lot of trail riding, the best bike for exercise would probably be a mountain bike. For a person who uses bikes for transportation and exercise, but doesn’t go off-road, the hybrid bike build is a good type of bike.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
These guys are awesome. After work, I got to my bike to discover my back tire was completely flat. It had a slow leak, so I was able to pump it up enough to make it to their shop. I got there 10 minutes before closing and they were able to fit me in. They replaced my tube and picked all of the glass shards out of my tire. Awesome customer service and they saved me from having to do this myself in the dark and the cold.
I brought my bike into Kyle's shop to fix the noise in my rear wheel. The mechanic suggested that I need to overhauled the rear hub for $30. The next day the noise came back even worst. I brought it back to the shop and they said it was the freewheel driver not the hub that needed to be work on and it would cost me extra $30 to overhauled it again plus the part to fix it. At this point I walked out of the shop and took my bike to David's world. The mechanic at David's world took a quick look at the rear hub and indicated that the axle was put back too tight when Kyle's mechanics were working on it and further identify the issue. I ended up paying David's world the $30 plus part to fix my bike, but the major different is that David's World has 30 Days services warranty claim. If you have any issue with your bike within the 30 days the service was performed you can bring it back and they will fix it no question ask.
The Bicycle Repair Shop is the place to be if you want to buy a new bike, need a repair or to rent a bike. These guy know everything about bikes and then some and at an amazing price. If you need your bike repaired they go above and beyond to help you get your bike repaired. If you are a tourist the shop has a great many bikes to choose from at an excellent price. I visited this shop last time I was in Seattle visiting my son and we rented the tandem bike it was a blast. My son bought a great bike and if he needs a tune up he goes to The Bicycle Repair Shop. This is the best bike shop in all of Seattle !!!!!!!
I chose to test these four levers after eliminating everything out there that’s not appropriate for a roadside emergency kit. That includes metal levers. They’re durable, but according to touring cyclist Ramona Marks, “Metal tire levers are trouble. It’s possible to rip your tube even with the plastic ones if you’re not careful, so metal is out of the question, and you don’t want to put pressure against the wheel rim with a metal lever.”
Maintenance is the best prevention. “Prevention is the best medicine, and if you’re taking care of your equipment it’s super key. Bikes don’t just fail. If they’re in really good working condition and you clean them at night, and you’re religious about it, bikes are kind of like cars — they’ll start talking to you if something is getting worn or getting creaky or needs to be replaced.”

Main types of bicycles are road, mountain, commuter/comfort and fitness bikes. There are more specific types and other names for bike types within that, such as urban bikes (same as commuter bikes), cruiser bikes, dual-sport bikes, hybrid bikes, fixed-gear bikes, cyclo-cross bikes, adventure road bikes (aka  all-road bikes, gravel bikes), road bikes, touring bikes and specialty bikes, like BMX.
×