On a very sunny Saturday I had a rear spoke break - you can imagine that no shop was willing to promise a quick repair! I was so fortunate to find this shop and will come back - Andy not only told me to come down and he'd get it fixed, he had his assistant work with another couple while he measured, cut to the right size, installed and trued the wheel while I waited! It was awesome, and the whole place had a great feel and good people. Best of all he charged a very fair $20 for all that work - I would have paid a premium for the quick service! After experiencing lots of attitude at other shops and poor service, this was a real find. I hope you will check them out, they have a great selection of bikes and accessories too! Good people and good craftsmanship should be rewarded.
Nice, helpful, friendly. Central location. Good bikes (I had two over two days.) Bikes had a water bottle cage (some places don't do that!) Provided helmets if needed (I didn't) and a one-sided pannier containing a decently strong but not super-heavy cable lock and a patch kit. Only quibbles: 1) The owner helping me with getting my bikes seemed to 'drop me' for too long when someone else walked in. He should have said to them, after asking what they were in for, that 'I'll be with you as soon as I'm finished with this person.' So I had to wait a little longer than desired, but not bad. 2) On my second day, the pannier bag fell off and got lost after I stopped for lunch, which required locking up the bike somewhere, so I took the bag into restaurant and re-attached it using the two velcro straps on the rear rack. I've used many panniers before, thought I did it correctly. But apparently I did not. So I paid $55 (cost) to replace everything in bag and bag. In hindsight, I wished I'd put a bungee around bag straps to really secure it to bike. PROBABLY MY FAULT. 3) Bring a second lock to lock quick-release front wheel, as decently strong but not super-heavy cable lock isn't long enough for both wheels and frame.I had a second cable lock.

It includes nine tools: seven hex bolts, one torx bolt (the star-shaped one), and a Phillips screwdriver (also the star-shaped one). Like Peter says in our guide, if you have a newer mountain bike or road bike it pays to take a quick look at what types of tools you need, as torx bolts are becoming more common. And a quick glance at the bottom of your shoes or derailleur bolts will confirm if a Phillips head is the right choice.

Every expert I spoke to recommended Pedro’s Tire Levers by name. They have a wide body—a different shape than other models we tested—and that prevents breakage, but more important, the broad, flat surface area of the tip helps it stay locked under your tire. When a lever slips from under the bead of the tire, you can end up repeatedly scraping your knuckles on the spokes of the wheel, which is so annoying. Pedro’s levers are small enough to fit into a saddlebag, are sold widely in bike shops, and even come with a lifetime guarantee. If one breaks, Pedro’s will replace it.
We like, and recommend, the Crankbrothers Speedier Lever. If you have to pick only one, go with the Pedro’s, but if you want a backup or have some hard tires to unseat, Crankbrothers is a great choice. It’s only one lever (as opposed to a set of two, like the Pedro’s) and it’s longer, so we didn’t pick it over the Pedro’s for portability reasons. But it’s an excellent tool. It has a wide handle you can grip with your whole hand. Like the Pedro’s, the tip is the right size and shape to prevent slipping and stay in place, and the shape of the handle happens to protect your knuckles if you do slip. Even in situations where I didn’t need it, I liked having it because it made me feel like a pro.
We focused on tools that would be useful to a commuter—someone trying to use a bike as a functional way to get around town, as opposed to riding recreationally (road biking and mountain biking). That said, it’s a wild and wooly bicycling world out there, and the streets are packed with so many different bikes, all shapes and sizes, new and old. Customizing your flat-fixing kit has advantages over buying a preassembled kit that always contains a tool (or two or three) that’s a piece of junk, or you don’t need. Or it’s missing something you do need. If you build your own kit, at least you know everything works. And you can add only what’s necessary for your specific bike without ending up with stuff you don’t need.
Patch kit:   Patch kits are easy to use, light and compact, and if you get more than one flat on a ride (it happens more than you’d expect), it can save you when you’ve already used your spare tube.   Plus, on a rear wheel, patching a tube can be faster than replacing it, as you can often do this without removing the wheel at all.  Another upcoming post is going to show you how to patch a tube.
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
Next to everything else that might go wrong with a bicycle on an extended ride, a flat is a relatively minor issue that can be easily repaired trailside, if the right tools are at hand. If they aren’t, a quick fix can turn into a long walk. Well-prepared riders will perform a tune-up regularly and clean their bikes after every ride. For the less-diligent, a well-stocked repair kit will suffice.
Let me go ahead and get the bad stuff out of the way. First of all, this stand is NOT the same level of quality as something you would find in a bicycle shop being used for the shop's repairs. it's quite a bit more flimsy, and the grip likes to rotate if you don't get the bike's center of gravity just right. The tool tray is also made out of a rather cheap plastic that can break easily at the rim. That being said, this stand is perfect for home users and makes mundane tasks like fixing a flat or cleaning the chain much easier. It easily holds my Raleigh Merit 3, and I don't worry about the thing falling even if the grip tilts a bit. The stand significantly shortened the time I needed to change an inner tube on my bicycle, and made me less worried about damaging something on the bike by jury-rigging a stand out of whatever I had lying around.
I chose to test these four levers after eliminating everything out there that’s not appropriate for a roadside emergency kit. That includes metal levers. They’re durable, but according to touring cyclist Ramona Marks, “Metal tire levers are trouble. It’s possible to rip your tube even with the plastic ones if you’re not careful, so metal is out of the question, and you don’t want to put pressure against the wheel rim with a metal lever.”
A two-stage hand pump tries to marry the best features of both types of pumps: the quick inflation of high volume that can achieve the higher psi ranges of high pressure. But to steal a quote from our floor pump guide, “You pump eight times or you pump 10 times—what does it matter?” That’s a quote from Daimeon Shanks, who at the time was a mechanic for the Garmin-Sharp pro tour team—that’s right, Tour de France, baby.

Be organized. “I like having everything be really small and super organized. I put all of my tools in CamelBak’s Tool Roll. It’s got little compartments, and I can separate tire changing stuff in one place, stuff like extra pedal cleats or an extra derailleur hanger in another, and it all rolls up into this tidy pouch. If I do have a repair, I can pull that one thing out and lay it out on the ground and it’s easy to work.”
Keychain style flashlight or headlamp, LED type, not incandescent:   The keychain style is tiny and lightweight, the headlamp style is a bit bulkier but easier to use.    You can get these for a couple of bucks or less at the local big box hardware store.  The LED ones are lighter, more durable and last considerably longer.   Very useful if you need to make a repair after dark!  I keep a keychain style one as a backup as I normally have a headlamp in my backpack.
Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Before I get started, I should mention that I never leave reviews. This is probably my first one on Yelp. These guys are just so great that I felt compelled to give them a shoutout. This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. These guys will give you their best and provide some laughs as well. Couldn't recommend them more!

Create emergency patches on tires or tubes with this Bike Tire Repair Kit. Each pack comes with everything you need to fix a flat, including a spokes wrench. When you find a puncture or nail hole in your riding essential, grab an application from this bicycle repair kit to hold in enough air so you can continue on your way until a replacement tire can be located. It includes adhesives and patches of different sizes for your convenience. Made of steel, the bicycle tire repair kit is durable and long-lasting. Keep the set with you at all times while riding your bicycle so that you have it in the event of an emergency. The size of the kit makes it easy to carry in a backpack or zippered cargo bag. Cover different sizes and types of holes and tears that make riding difficult with this Bike Tire Repair Kit.


Our favorite hand pump for commuters is the Lezyne Sport Drive HP, and you can read more specifics about why in our full-length guide, written by Dave Yasuda, a writer and tester with over 30 years in the saddle. To sum it up, Lezyne makes pumps with an extendable rubber tube that connects to your tire valve, and that’s the difference between awkward and demoralizing. It’s not the only company that does so, but it is one of the few, and it does it the best. The Sport Drive HP can adapt to any tire valve, has no small fussy parts to lose, and inflates more easily to higher psi levels than anything we tested without floor leverage.
Let me go ahead and get the bad stuff out of the way. First of all, this stand is NOT the same level of quality as something you would find in a bicycle shop being used for the shop's repairs. it's quite a bit more flimsy, and the grip likes to rotate if you don't get the bike's center of gravity just right. The tool tray is also made out of a rather cheap plastic that can break easily at the rim. That being said, this stand is perfect for home users and makes mundane tasks like fixing a flat or cleaning the chain much easier. It easily holds my Raleigh Merit 3, and I don't worry about the thing falling even if the grip tilts a bit. The stand significantly shortened the time I needed to change an inner tube on my bicycle, and made me less worried about damaging something on the bike by jury-rigging a stand out of whatever I had lying around.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
We're Arizona's top rated and 5 times running "America's Best" Rated Bike Shop by the NBDA.  From mountain bikes, kids, comfort, fitness and road bikes we sell and service them all! Are E-bikes your thing? Our Gilbert location Is our hub for electric bike sales and service. Swing by and see us... Family owned and operated by Brandee and Al since 2001.
A good patch will stick to your tube enough to keep air from leaking out. A great patch will act like a second skin and actually strengthen the tube where it’s applied, flexing and stretching with the tire. After 36 hours of testing, our official endorsement goes to the Rema TT 02 Touring Repair Kit. Its patches do everything other patches do, just better. The edge of the patch is also ruffled, which provides more edge surface area to bond—that’s a good thing.
I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
×