A pair of disposable latex gloves:  Not absolutely necessary, but good for keeping grease and grime off your hands during a repair.  Also, nice to have in an emergency when it starts raining and the temperature drops 20 degrees and you don’t have a pair of regular gloves.   Just keeping your hands dry and the wind from directly blowing on them makes a huge difference in comfort.
Professional mountain biker Rebecca Rusch has been on plenty of long rides and experienced enough mechanical failures to know what makes a fully-stocked repair kit. One of her recent journeys, a 1,200-mile journey through the jungles of Vietnam, Laos and Cambodia along the Ho Chi Minh Trail required the utmost degree of preparedness — “We brought with us a lot of extra bearings, o-rings, stuff that you would never be able to find in Laos and Cambodia. Before I go out on these big adventures, I replace every bearing in my bike, my fork got a total rebuild — everything is in pristine condition,” says Rusch.

Over the years, I’ve come across plenty of articles that claim to tell you how to build up your cycling toolkit for cheap. Somehow the word “cheap” stops recurring in the long list of “essential” bike repair bits and pieces. The truth is, there is no real way to build a whole shop of tools all at once without plopping down a few hundred bucks. But in an attempt to show everyone that not all of us truly need a full complement of bike tools, I present the truest, most budget-conscious, and barest of bones options to you.

It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.

Since then, I’ve found a few decent alternatives to my dilemma: The Venzo Pro Mechanic Stand that runs at about $88, and the Cave Competitor Service Post for $59. While there are other alternatives out there—sometimes cheaper ones—these are the two that I think are actually worth the price. I can’t really vouch for any others out there. But there just ain’t getting around this one. You’ll need something to hold your bike while you work on it.
More than any other tool in the kit, a reliable lever makes changing a tire easier, especially if you have road bike tires, which are difficult to remove. However, throughout testing, levers seemed to be the one item more prone to failure and poor design than anything else. For example, I found a random orange lever floating around my basement and I threw it in the test pool for fun—it seemed solid enough … until I began prying at the rim of a tire. It bent directly in half, slowly and smoothly, like taffy, and then was boomerang shaped forevermore.
Do not take your Bike to Kyle's Bike Shop they handled my bike so poorly they can not work on Vintage Schwinn' and the attitude they had if it wasn't a high dollar bike don't expect good service. I had to find my own parts, had to take the bike back twice to get the wheel trued and they ruined my bike it is so scrapped up the Schwinn is gone on the side of the bike. If you care about your bike do not take it here.
Otherwise, this tool should serve the average commuter well. Specifically, we think you’ll find the size 4, 5, and 6 hex keys, extremely common sizes in bicycles, very helpful. They’ll adjust seat-post heights or let you remove the saddle entirely, or tighten a loose stem that’s always rattling apart. The Phillips head will tighten loose bolts on shoe cleats or the rear derailleur. The most common use for the torx would be adjusting disc brakes if you have ’em.
We're Arizona's top rated and 5 times running "America's Best" Rated Bike Shop by the NBDA.  From mountain bikes, kids, comfort, fitness and road bikes we sell and service them all! Are E-bikes your thing? Our Gilbert location Is our hub for electric bike sales and service. Swing by and see us... Family owned and operated by Brandee and Al since 2001.

It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
A plastic garbage bag, or $2 disposable poncho:  Just in case of an unexpected downpour or getting caught out after dark.   More than once, I’ve gone for a ride on a beautiful day with a perfect forecast, not taken a jacket and had the weather go south on me.  Being able to cover up can mean the difference between just mild discomfort or a freezing cold, shivering ride home!
A bicycle costs anywhere from $250-$9,000 depending what type and quality of bike you want. A utility bike from a department store might cost $300-$500, but experts caution that it will be quite a bit heavier and not as well constructed as other bikes. For a durable, lightweight bike with front-suspension and decent parts, it’s reasonable to pay $750-$1,200. You might be able to pay slightly less, but expect to need some repairs after several months of heavy use.
Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.
If you have just a short time in Seattle there is only one way to see the city. Walk at 2.5 miles an hour? I don't think so. Take buses and trams that you have to wait for and that might not even get you where you need to go? No way Jose. Drive your car? Hahahaha get outta here, don't even talk to me. But what about a BICYCLE??? Now that's the ticket. The Bicycle Repair Shop does rentals by the hour or by the day. They have reasonable rates. They have solid, lightweight hybrid bikes so you can tackle train tracks and brick streets and hills. They also have road bikes for the more experienced. You can reserve online in advance. You get a helmet and a lock with your rental. The staff in the shop are friendly and will suggest routes and point out hills if you're new to the area. And believe me these hills are no joke! I had a great time in Seattle and it's all thanks to this business. Next time I visit I am definitely doing this again.
We offer several bicycle repair packages, or individual services in the case that you don’t need a full “tune-up”. Whether it’s a small brake adjustment or a complete bike overhaul, we’re happy to help. Our highly experienced staff is here to answer any questions you may have and will help get you and your bike back on the road as quickly as possible.
×