There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.


It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
This gentleman is a true professional!! He is an ex-Marine and I will tell you that he represents them well. He is honest, knowledgeable and extremely reasonable. He repaired my son's bike while I waited and went over the whole bike and made the required adjustments replaced an inner tube and all for 20 dollars!!All the kids in the area pass by and call him by his first name. I will recommend him to everyone I know since there are very little of them out there!!
A good patch will stick to your tube enough to keep air from leaking out. A great patch will act like a second skin and actually strengthen the tube where it’s applied, flexing and stretching with the tire. After 36 hours of testing, our official endorsement goes to the Rema TT 02 Touring Repair Kit. Its patches do everything other patches do, just better. The edge of the patch is also ruffled, which provides more edge surface area to bond—that’s a good thing.
Some years ago, I used to live on my bike. Riding around daily through any weather condition was bound to quickly wear down on the bike over time. I like some of the stuff that you have in your toolkit. I would say zip ties are actually really convenient, because when something came loose you could go ahead and use those to fasten them down to keep on moving ahead until you had enough time to fix it or get it checked at a bike repair shop.
I brought my bike into Kyle's shop to fix the noise in my rear wheel. The mechanic suggested that I need to overhauled the rear hub for $30. The next day the noise came back even worst. I brought it back to the shop and they said it was the freewheel driver not the hub that needed to be work on and it would cost me extra $30 to overhauled it again plus the part to fix it. At this point I walked out of the shop and took my bike to David's world. The mechanic at David's world took a quick look at the rear hub and indicated that the axle was put back too tight when Kyle's mechanics were working on it and further identify the issue. I ended up paying David's world the $30 plus part to fix my bike, but the major different is that David's World has 30 Days services warranty claim. If you have any issue with your bike within the 30 days the service was performed you can bring it back and they will fix it no question ask.

These guys are awesome.  After work, I got to my bike to discover my back tire was completely flat.  It had a slow leak, so I was able to pump it up enough to make it to their shop.  I got there 10 minutes before closing and they were able to fit me in.  They replaced my tube and picked all of the glass shards out of my tire.  Awesome customer service and they saved me from having to do this myself in the dark and the cold.

Spare tube:  Sometimes, a tube is just too damaged to be patched, or has had a failure such as the valve stem breaking off which isn’t something that can be patched.   To save weight and space, I usually keep a lightweight version of the right size tube for my bike.   Since one of the first things I do with most bikes that I own is switch them over to heavy-duty thorn resistant tubes, I just take one of the originals and put that in the toolkit.
Inside Student Union across from College Optical, the UCF Bike Repair Service is provided for students with bike problems. Students may come, free of charge, and have their bikes repaired with quality service by our Bike Repair Team. Service include: Inflate tires, change tubes, brake adjustments, tighten crankset, loose handlebars, adjust gears, and brake cable installation. Bikes can also be reserved here as part of the Bike Share program.
×