Our favorite hand pump for commuters is the Lezyne Sport Drive HP, and you can read more specifics about why in our full-length guide, written by Dave Yasuda, a writer and tester with over 30 years in the saddle. To sum it up, Lezyne makes pumps with an extendable rubber tube that connects to your tire valve, and that’s the difference between awkward and demoralizing. It’s not the only company that does so, but it is one of the few, and it does it the best. The Sport Drive HP can adapt to any tire valve, has no small fussy parts to lose, and inflates more easily to higher psi levels than anything we tested without floor leverage.
We spoke to a broad spectrum of cyclists—from a pro racer to a bike messenger turned mechanic to a touring cyclist who has logged thousands of miles throughout Europe—to find out what items they find indispensable. We sorted through 40 tire levers, almost 30 different kinds of patches, 120 different hand pumps, and 57 seat bags before we narrowed our choices for testing. And then we changed and patched tires more than 50 times, using four different bikes, five different wheels, six different tires, and almost 10 different sizes of tubes. After 96 hours of combined testing, we agree these essentials are some of the best you can buy.
More than any other tool in the kit, a reliable lever makes changing a tire easier, especially if you have road bike tires, which are difficult to remove. However, throughout testing, levers seemed to be the one item more prone to failure and poor design than anything else. For example, I found a random orange lever floating around my basement and I threw it in the test pool for fun—it seemed solid enough … until I began prying at the rim of a tire. It bent directly in half, slowly and smoothly, like taffy, and then was boomerang shaped forevermore.
To pick the right size bicycle, you want to measure your height, and specifically your inseam (inside leg), in proportion to the size of the bike frame. The inseam measurement determines the seat height, or the “stack.” Next, you must calculate the “reach,” which is the horizontal distance between the bottom of the frame and the head of the bike -- or, in layman’s terms, the distance between seat and handlebars.
I bought this book to supplement "Anybody's Bike Book" because I always like to get a second opinion. This book uses photos extensively rather than drawings as in the other book. They are well composed and quite helpful providing additional detailed information in a clear, conciseful manner. Information is provided in heirarchy format and geared from initial purchase to daily maintenance of my two wheeled friend. Good book!
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
A plastic garbage bag, or $2 disposable poncho:  Just in case of an unexpected downpour or getting caught out after dark.   More than once, I’ve gone for a ride on a beautiful day with a perfect forecast, not taken a jacket and had the weather go south on me.  Being able to cover up can mean the difference between just mild discomfort or a freezing cold, shivering ride home!
I bought this book to supplement "Anybody's Bike Book" because I always like to get a second opinion. This book uses photos extensively rather than drawings as in the other book. They are well composed and quite helpful providing additional detailed information in a clear, conciseful manner. Information is provided in heirarchy format and geared from initial purchase to daily maintenance of my two wheeled friend. Good book!
Broadly speaking there are two major wheel sizes – 700c for road bikes and 26 inch off-road wheels. However there are a whole variety of older, less common wheel sizes and of course fold up bikes have much smaller wheels altogether. Repairing a puncture is not an emergency! It’s a basic procedure that every cyclist should be able to to perform, but doing it correctly involves more steps than many people realise. Wheel building is often seen as the most artful skill in bicycle maintenance, and separates the professionals from the amateurs but that doesn’t mean you should consider it out of reach. Truing a slightly misaligned wheel is a cycle maintenance job that almost any cyclist can perform.
×