The Pedro’s lever slipped only once throughout testing, though that may have been my fault because I was spaced out after changing 16 different tires. So they’re not foolproof, but they are far and away more reliable than the next closest competitor, from Park Tool, because the small, rounded tip on that one is hard to keep seated under the tire. Not impossible, but I wouldn’t choose it over Pedro’s.
Since then, I’ve found a few decent alternatives to my dilemma: The Venzo Pro Mechanic Stand that runs at about $88, and the Cave Competitor Service Post for $59. While there are other alternatives out there—sometimes cheaper ones—these are the two that I think are actually worth the price. I can’t really vouch for any others out there. But there just ain’t getting around this one. You’ll need something to hold your bike while you work on it.

Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
Basically, you’re stuck with toggling between systems for the advantage of a few pumps, and it doesn’t seem worth it. In the original iteration of this guide, I tested 12 pumps and inflated three different tires completely full to their psi rating, and measured how many pumps it took. Yasuda did similarly for his revamped full-length exploration. That’s 36 tires, and I can guarantee there is no difference between 50 pumps and 100—it’s all terrible.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
It has some useful information for basic repairs... not so heavy on the maintenance side but there is some in there. The pictures and drawings are in black and white, but mostly visible. Only a few are difficult to see. However, they are in 2-dimensions and they don't show you HOW to do the thing, they only show you the general area and the part you want to manipulate. The phrasing in the instructions can be hard to follow without a good visual reference unless you're already a master bike mechanic (which you aren't if you're thinking about buying this). So, buy this for general reference and rely on Youtube for video. The two together are better than either one alone.

Before I get started, I should mention that I never leave reviews. This is probably my first one on Yelp. These guys are just so great that I felt compelled to give them a shoutout. This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. These guys will give you their best and provide some laughs as well. Couldn't recommend them more!

Whether you ride a single, 7, or 10 speed bike or anything in between, you will need a slightly different chain. The major difference is that they come in varying widths to accomodate the different spaces between the gears, but quality of construction is also a factor in choosing a chain. Inspecing the chain should be a part of your regular cycle maintenance procedure- It’s important to keep a chain well lubricated, but oil will also attract dirt and so different oils for specific riding conditions are available. Remember to clean your chain regularly to get the longest life out of it and the gears.
×