I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
Based on what we found, we chose the most relevant items and used them all. To test patches, I repaired holes using four different types of patches, from Novara (REI’s now-discontinued house brand), Park Tool, and Rema. Patching a tube isn’t hard but there are a few tricks, and the key was attention to detail and patience. I was extremely diligent in following proper patch procedure, which includes a thorough sanding of the entire area to be patched (for max stickiness) and properly letting the vulcanizer dry on both surfaces before applying. For the peel-and-stick patches, I went so far as to prep the area with canned air to ensure as tight a seal as we could possibly muster.
A good patch will stick to your tube enough to keep air from leaking out. A great patch will act like a second skin and actually strengthen the tube where it’s applied, flexing and stretching with the tire. After 36 hours of testing, our official endorsement goes to the Rema TT 02 Touring Repair Kit. Its patches do everything other patches do, just better. The edge of the patch is also ruffled, which provides more edge surface area to bond—that’s a good thing.

It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.


Any bike that gets ridden seriously as transportation or on long rides needs at least a basic tool/emergency kit, and the knowledge to use it, unless the rider is always in a position to call a friend with a car or a cab when their bike needs a quick fix on the road.  If you never travel more than a few miles, this can be overkill, and calling a friend or a cab may be just the ticket,  but if you want to be more self reliant, this is something you should seriously consider.  This list may sound like an awful lot of stuff to carry, but really, it only weighs a few lbs and fits in a small, under-seat bag that comes off quickly so I don’t have to leave it with the bike if theft is a concern.  If you always carry a regular rack top bag, you can also just put all this in a small nylon bag and throw it in there, but I prefer an under-seat bag.

I just got a tune up on my bike and it rides so much better now! It takes half as much effort to petal, it is like a new bike. The guys who work there are so nice and always make you feel like your time is important. They don't overcharge or sell you things you don't need. I thought for sure I needed a new chain, but as it turns out, it's fine! He gave me some extra foam for my bike helmet, free of charge! I'll definitely come back here for all my bike needs!


Whether you ride a single, 7, or 10 speed bike or anything in between, you will need a slightly different chain. The major difference is that they come in varying widths to accomodate the different spaces between the gears, but quality of construction is also a factor in choosing a chain. Inspecing the chain should be a part of your regular cycle maintenance procedure- It’s important to keep a chain well lubricated, but oil will also attract dirt and so different oils for specific riding conditions are available. Remember to clean your chain regularly to get the longest life out of it and the gears.
×