A pair of disposable latex gloves: Not absolutely necessary, but good for keeping grease and grime off your hands during a repair. Also, nice to have in an emergency when it starts raining and the temperature drops 20 degrees and you don’t have a pair of regular gloves. Just keeping your hands dry and the wind from directly blowing on them makes a huge difference in comfort.
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
It includes nine tools: seven hex bolts, one torx bolt (the star-shaped one), and a Phillips screwdriver (also the star-shaped one). Like Peter says in our guide, if you have a newer mountain bike or road bike it pays to take a quick look at what types of tools you need, as torx bolts are becoming more common. And a quick glance at the bottom of your shoes or derailleur bolts will confirm if a Phillips head is the right choice.
There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
In spite of seat bags’ diminutive size, a lot of people really, really want them to accommodate more stuff. If that’s you, the medium and large seat bag (but not the small) have an extendable gill at the bottom, which you can see in the image up top. It zips open to create more room. With it unzipped, we could cram a wallet, keys, and phone inside the medium as well.
Many bikes, including older models and track bikes, have bolts attaching the wheels to the frame instead of quick-release levers. If your wheels are bolted on, in most cases you’ll need a 15 mm wrench to remove it. We didn’t test wrenches, because there aren’t that many tiny 15 mm wrenches, but the GearWrench 15mm 12-Point Stubby Combination Wrench is perfect for stuffing into a flat kit and Amazon reviewers seem to think the same. Our experts also recommended the Surly Jethro Tule, but it’s expensive and harder to find.
A bicycle costs anywhere from $250-$9,000 depending what type and quality of bike you want. A utility bike from a department store might cost $300-$500, but experts caution that it will be quite a bit heavier and not as well constructed as other bikes. For a durable, lightweight bike with front-suspension and decent parts, it’s reasonable to pay $750-$1,200. You might be able to pay slightly less, but expect to need some repairs after several months of heavy use.
We rented a tandem bike from here for an hour, and they were super chill! We dropped by on a Sunday and decided to go eat first; Andy, one of the owners, was awesome about holding the bike for us while we went to eat before renting. We enjoyed our ride for just over an hr, but Andy was also super relaxed about our return time and only charged us for an hour. We had a fantastic time and would definitely recommend renting bikes from here!
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
These guys are awesome. After work, I got to my bike to discover my back tire was completely flat. It had a slow leak, so I was able to pump it up enough to make it to their shop. I got there 10 minutes before closing and they were able to fit me in. They replaced my tube and picked all of the glass shards out of my tire. Awesome customer service and they saved me from having to do this myself in the dark and the cold.