It includes nine tools: seven hex bolts, one torx bolt (the star-shaped one), and a Phillips screwdriver (also the star-shaped one). Like Peter says in our guide, if you have a newer mountain bike or road bike it pays to take a quick look at what types of tools you need, as torx bolts are becoming more common. And a quick glance at the bottom of your shoes or derailleur bolts will confirm if a Phillips head is the right choice.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Where to begin?! Long story made somewhat short. I bookmarked this place because I saw their dog Kaya and was sold. Lol. But they had 5 stars too so that helped. Amazing people. Very down-to-earth. Took the bikes down the path to Discovery Park. If you're in-shape and do mild cardio, then it should be an ok ride. I don't do cardio and I found myself trying to sell my soul like 15 times just to get to the top of some hills. Lol. Made it to the Ballard locks and actually got to see a boat pass through! This is the off-season so not much boat traffic. Steve, an engineer we met there, said peak time will start in May. Ate lunch at Ann's in Ballard. Delish shrimp sate! I busted my tire in a pothole and had to make a trip to REI. Which wasn't awful because we wanted to go there anyway. The city was tough to ride in at 5:00pm and we rode the sidewalk most of the way back due to the congestion. Some pedestrians are obvious to you and I almost ran over a few people.. By choice. Lol. Made it back right before they closed at 6:00pm. Easy peasy! Notes: Take some water. Take some pictures. The ride is beautiful so don't rush through. Get there before noon to give yourself some time to cruise.
Otherwise, this tool should serve the average commuter well. Specifically, we think you’ll find the size 4, 5, and 6 hex keys, extremely common sizes in bicycles, very helpful. They’ll adjust seat-post heights or let you remove the saddle entirely, or tighten a loose stem that’s always rattling apart. The Phillips head will tighten loose bolts on shoe cleats or the rear derailleur. The most common use for the torx would be adjusting disc brakes if you have ’em.
Since then, I’ve found a few decent alternatives to my dilemma: The Venzo Pro Mechanic Stand that runs at about $88, and the Cave Competitor Service Post for $59. While there are other alternatives out there—sometimes cheaper ones—these are the two that I think are actually worth the price. I can’t really vouch for any others out there. But there just ain’t getting around this one. You’ll need something to hold your bike while you work on it.
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.

Dennis Bailey has been actively involved in bike repair and maintenance for almost two decades. He has worked on bikes on bike tours in the United States, Europe, and Latin America. Keith Gates has been repairing bikes for more than 30 years and provides personalized service as the owner of A-1 Cycling, with locations in Manassas and Herndon, Virginia.
This gentleman is a true professional!! He is an ex-Marine and I will tell you that he represents them well. He is honest, knowledgeable and extremely reasonable. He repaired my son's bike while I waited and went over the whole bike and made the required adjustments replaced an inner tube and all for 20 dollars!!All the kids in the area pass by and call him by his first name. I will recommend him to everyone I know since there are very little of them out there!!
Keychain style flashlight or headlamp, LED type, not incandescent:   The keychain style is tiny and lightweight, the headlamp style is a bit bulkier but easier to use.    You can get these for a couple of bucks or less at the local big box hardware store.  The LED ones are lighter, more durable and last considerably longer.   Very useful if you need to make a repair after dark!  I keep a keychain style one as a backup as I normally have a headlamp in my backpack.
One key difference, that you can see in the photo, is that the BV uses buckles instead of Velcro on the straps that attach the bag to the underside of the saddle, something much more important than it may seem. A pair of bike shorts (or any shorts) will shred quickly if they’re rubbing against that tiny bit of Velcro protruding from the side of the bag, and it’s sure to destroy expensive sweaters and gym clothes if you stuff the bag into your backpack or messenger bag.
Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.
We like, and recommend, the Crankbrothers Speedier Lever. If you have to pick only one, go with the Pedro’s, but if you want a backup or have some hard tires to unseat, Crankbrothers is a great choice. It’s only one lever (as opposed to a set of two, like the Pedro’s) and it’s longer, so we didn’t pick it over the Pedro’s for portability reasons. But it’s an excellent tool. It has a wide handle you can grip with your whole hand. Like the Pedro’s, the tip is the right size and shape to prevent slipping and stay in place, and the shape of the handle happens to protect your knuckles if you do slip. Even in situations where I didn’t need it, I liked having it because it made me feel like a pro.
Now you might be wondering: “I’m carrying a tube; why carry patches at all?” As insurance for the unforeseeable. Wirecutter senior editor Christine Ryan admits she didn’t use to pack them, but said, “I’ve regretted that decision when I’ve had a flat on a ride, used my spare tube, and then, half an hour later, had a second flat. Also, lots of people aren’t very good at figuring out—or don’t take the time to figure out—what caused their flat and remove the cause: thorn, eensy bit of glass, whatever. Then they promptly have a second flat, and everyone else laughs at them.”
First, carbon. You already know you don’t need it for your casual weekend pursuits, because you’re not counting ounces the way a professional road racer would. But to quote an article from Velonews, “Remember that professional athletes operate in an entirely different environment than the rest of us. They are all very close to each other in terms of fitness, and they are also all very close to being the absolute best a human being can be. In short, you’re much better off upgrading your legs and dropping body fat through proper training and diet.”
Return: Bicycle and lock must be returned by the end of the loan period. User will be charged a $10.00/day late fee. After 10 business days user will be charged the full cost of the bicycle ($350) and rented equipment ($50 for lock and/or key). Failure to return bicycle, helmet and lock will subject user to legal liability of $400.00, as well as having student account placed on hold.
×