It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
I chose to test these four levers after eliminating everything out there that’s not appropriate for a roadside emergency kit. That includes metal levers. They’re durable, but according to touring cyclist Ramona Marks, “Metal tire levers are trouble. It’s possible to rip your tube even with the plastic ones if you’re not careful, so metal is out of the question, and you don’t want to put pressure against the wheel rim with a metal lever.”
If you are planning on going on a multi-day ride or just riding a long distance in a day, you should have something for first aid, just in case. Unfortunately, almost everyone who cycles frequently will go down at least once in their life. This kit can be really small and compact and can include bandages, some gauze, and a small bottle of a disinfectant.
Packed with basic tools, this compact tin rescues puncture-interrupted bike trips. Pedaling away to a picnic spot with a pal, you hear a disconcerting "pop!". Your two-wheeler is now down one wheel, and unless you've got mad unicycle skills, you need tools. Good thing you brought this handsome, compact tin. Just break out the metal tire levers and patch kit, and you're rolling along again in no time. The six-sided, dog bone-style hex wrench adjusts the most common bike screws and bolts and screws. Made in China.
These folks took me in right away, diagnosed and fixed my stripped handle bar clamps and had me on my way to work in about 15 minutes. Friendly, straightforward, understands the rider's objectives (in my case, how do I get home from work). Not to mention, the fee was reasonable. I have been in many bike repair places in my 6 decades. This is the best.
There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
The SGA Bike Share is open to all students with a valid UCF Card. There is no rental fee to rent a bicycle, lock, helmet, and light for one work day. Participants may rent and return our bikes from the following four locations: the Student Union, Recreation and Wellness Center, RWC @ Knights Plaza and Lake Claire Apartments. Use of our equipment is strictly on a first-come-first-served basis.
This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement.
More than any other tool in the kit, a reliable lever makes changing a tire easier, especially if you have road bike tires, which are difficult to remove. However, throughout testing, levers seemed to be the one item more prone to failure and poor design than anything else. For example, I found a random orange lever floating around my basement and I threw it in the test pool for fun—it seemed solid enough … until I began prying at the rim of a tire. It bent directly in half, slowly and smoothly, like taffy, and then was boomerang shaped forevermore.
A plastic garbage bag, or $2 disposable poncho: Just in case of an unexpected downpour or getting caught out after dark. More than once, I’ve gone for a ride on a beautiful day with a perfect forecast, not taken a jacket and had the weather go south on me. Being able to cover up can mean the difference between just mild discomfort or a freezing cold, shivering ride home!
The Knights Helping Knights Pantry is a student driven program at the University of Central Florida with the goal of assisting students through financially tough times. Donations that are either brought to the Pantry or are left in one of our 15 drop boxes on campus are provided by faculty, staff and students. Student organizations, departments and individuals on campus also organize food drives that benefit the Pantry.