It has some useful information for basic repairs... not so heavy on the maintenance side but there is some in there. The pictures and drawings are in black and white, but mostly visible. Only a few are difficult to see. However, they are in 2-dimensions and they don't show you HOW to do the thing, they only show you the general area and the part you want to manipulate. The phrasing in the instructions can be hard to follow without a good visual reference unless you're already a master bike mechanic (which you aren't if you're thinking about buying this). So, buy this for general reference and rely on Youtube for video. The two together are better than either one alone.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
The retractable tube is stored inside the body of the pump when not in use, and it can attach to either a Schrader or a Presta valve, the two types of valves you’ll see. Some pumps can accommodate only one type, making them less universal. Toggling between the two is simple, which can’t be said of other models with itty parts that require nerves of steel to handle on a good day, let alone while wearing gloves, crouching in the wind, oblivious to the sewer grate a few feet away.
Riding the bus with three infants in a stroller is no easy task, especially when you realize you have a flat tire as soon as you step foot on the pavement of 2nd and University. Luckily, I found The Bicycle Repair Shop. Andy happily filled my tire with air, and when it was flat again an hour later, found a replacement tube in minutes. He changed the tire with the babies still in the stroller! This was such an amazing experience that totally made a fun day possible for us! Thank you, Andy!
As you mentioned, it is surprising how often you can get multiple flat tires on while riding, particularly on longer sprints. The tip about bringing a patch kit in your bike repair kit can be incredibly helpful if you’ve already had one flat tire. I agree that all you listed seems like an awful lot to carry, but it’s always better to be safe than sorry, isn’t it?
First, I researched. I looked at Amazon’s top-rated products and their user reviews. Then I consulted Bicycling magazine, Gear Junkie, Bike Radar, Outside, and the occasional bit by Lennard Zinn via Velonews. I also found some worthwhile discussions at Bike Forums. Then I spoke with four experts, Ramona Marks, Scott Karoly, Cari Z, and Alison Tetrick, riders from all across the spectrum, who tour, repair, and race.
Where to begin?! Long story made somewhat short. I bookmarked this place because I saw their dog Kaya and was sold. Lol. But they had 5 stars too so that helped. Amazing people. Very down-to-earth. Took the bikes down the path to Discovery Park. If you're in-shape and do mild cardio, then it should be an ok ride. I don't do cardio and I found myself trying to sell my soul like 15 times just to get to the top of some hills. Lol. Made it to the Ballard locks and actually got to see a boat pass through! This is the off-season so not much boat traffic. Steve, an engineer we met there, said peak time will start in May. Ate lunch at Ann's in Ballard. Delish shrimp sate! I busted my tire in a pothole and had to make a trip to REI. Which wasn't awful because we wanted to go there anyway. The city was tough to ride in at 5:00pm and we rode the sidewalk most of the way back due to the congestion. Some pedestrians are obvious to you and I almost ran over a few people.. By choice. Lol. Made it back right before they closed at 6:00pm. Easy peasy! Notes: Take some water. Take some pictures. The ride is beautiful so don't rush through. Get there before noon to give yourself some time to cruise.
Spare tube: Sometimes, a tube is just too damaged to be patched, or has had a failure such as the valve stem breaking off which isn’t something that can be patched. To save weight and space, I usually keep a lightweight version of the right size tube for my bike. Since one of the first things I do with most bikes that I own is switch them over to heavy-duty thorn resistant tubes, I just take one of the originals and put that in the toolkit.
It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.
These are some great ideas, especially the simple ones like bringing a garbage bag. That’s something so easy and cheap that it’s easy to forget entirely, but as you say, it can make a huge difference in the right circumstances. It’s also good that you discuss some minor bike repairs. That’s another thing that can salvage or destroy your ride. You want to be as prepared as possible for the best possible experience.
Inside Student Union across from College Optical, the UCF Bike Repair Service is provided for students with bike problems. Students may come, free of charge, and have their bikes repaired with quality service by our Bike Repair Team. Service include: Inflate tires, change tubes, brake adjustments, tighten crankset, loose handlebars, adjust gears, and brake cable installation. Bikes can also be reserved here as part of the Bike Share program.