Over the years, I’ve come across plenty of articles that claim to tell you how to build up your cycling toolkit for cheap. Somehow the word “cheap” stops recurring in the long list of “essential” bike repair bits and pieces. The truth is, there is no real way to build a whole shop of tools all at once without plopping down a few hundred bucks. But in an attempt to show everyone that not all of us truly need a full complement of bike tools, I present the truest, most budget-conscious, and barest of bones options to you.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Otherwise, this tool should serve the average commuter well. Specifically, we think you’ll find the size 4, 5, and 6 hex keys, extremely common sizes in bicycles, very helpful. They’ll adjust seat-post heights or let you remove the saddle entirely, or tighten a loose stem that’s always rattling apart. The Phillips head will tighten loose bolts on shoe cleats or the rear derailleur. The most common use for the torx would be adjusting disc brakes if you have ’em.
In spite of seat bags’ diminutive size, a lot of people really, really want them to accommodate more stuff. If that’s you, the medium and large seat bag (but not the small) have an extendable gill at the bottom, which you can see in the image up top. It zips open to create more room. With it unzipped, we could cram a wallet, keys, and phone inside the medium as well.
Main types of bicycles are road, mountain, commuter/comfort and fitness bikes. There are more specific types and other names for bike types within that, such as urban bikes (same as commuter bikes), cruiser bikes, dual-sport bikes, hybrid bikes, fixed-gear bikes, cyclo-cross bikes, adventure road bikes (aka  all-road bikes, gravel bikes), road bikes, touring bikes and specialty bikes, like BMX.

I brought my bike into Kyle's shop to fix the noise in my rear wheel. The mechanic suggested that I need to overhauled the rear hub for $30. The next day the noise came back even worst. I brought it back to the shop and they said it was the freewheel driver not the hub that needed to be work on and it would cost me extra $30 to overhauled it again plus the part to fix it. At this point I walked out of the shop and took my bike to David's world. The mechanic at David's world took a quick look at the rear hub and indicated that the axle was put back too tight when Kyle's mechanics were working on it and further identify the issue. I ended up paying David's world the $30 plus part to fix my bike, but the major different is that David's World has 30 Days services warranty claim. If you have any issue with your bike within the 30 days the service was performed you can bring it back and they will fix it no question ask.
Basically, you’re stuck with toggling between systems for the advantage of a few pumps, and it doesn’t seem worth it. In the original iteration of this guide, I tested 12 pumps and inflated three different tires completely full to their psi rating, and measured how many pumps it took. Yasuda did similarly for his revamped full-length exploration. That’s 36 tires, and I can guarantee there is no difference between 50 pumps and 100—it’s all terrible.
One key difference, that you can see in the photo, is that the BV uses buckles instead of Velcro on the straps that attach the bag to the underside of the saddle, something much more important than it may seem. A pair of bike shorts (or any shorts) will shred quickly if they’re rubbing against that tiny bit of Velcro protruding from the side of the bag, and it’s sure to destroy expensive sweaters and gym clothes if you stuff the bag into your backpack or messenger bag.
A multitool is a highly versatile piece of repair equipment that can address most of your maintenance needs. Ideally, you should use it before a ride to tighten and adjust everything properly, but sometimes it’s necessary on a ride as well. If you encounter a loose screw, realize your saddle height is not right, or that your brakes need tightening, you will be happy to have it.

Nice, helpful, friendly. Central location. Good bikes (I had two over two days.) Bikes had a water bottle cage (some places don't do that!) Provided helmets if needed (I didn't) and a one-sided pannier containing a decently strong but not super-heavy cable lock and a patch kit. Only quibbles: 1) The owner helping me with getting my bikes seemed to 'drop me' for too long when someone else walked in. He should have said to them, after asking what they were in for, that 'I'll be with you as soon as I'm finished with this person.' So I had to wait a little longer than desired, but not bad. 2) On my second day, the pannier bag fell off and got lost after I stopped for lunch, which required locking up the bike somewhere, so I took the bag into restaurant and re-attached it using the two velcro straps on the rear rack. I've used many panniers before, thought I did it correctly. But apparently I did not. So I paid $55 (cost) to replace everything in bag and bag. In hindsight, I wished I'd put a bungee around bag straps to really secure it to bike. PROBABLY MY FAULT. 3) Bring a second lock to lock quick-release front wheel, as decently strong but not super-heavy cable lock isn't long enough for both wheels and frame.I had a second cable lock.
Friction gear systems are a lot simpler to adjust, because the movement of the derailer cable can be modulated as you ride, every time you change the gear- they require less cycle maintenance. Modern index shifting systems are a little more complicated because each ‘click’ must release the exact right amount of cable to allow the derailer to move the correct distance to move the chain from one gear to another. Setting up and adjusting a derailer is not difficult and requires only basic tools, but there is a methodical procedure to follow.
×