It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement.
Where to begin?! Long story made somewhat short. I bookmarked this place because I saw their dog Kaya and was sold. Lol. But they had 5 stars too so that helped. Amazing people. Very down-to-earth. Took the bikes down the path to Discovery Park. If you're in-shape and do mild cardio, then it should be an ok ride. I don't do cardio and I found myself trying to sell my soul like 15 times just to get to the top of some hills. Lol. Made it to the Ballard locks and actually got to see a boat pass through! This is the off-season so not much boat traffic. Steve, an engineer we met there, said peak time will start in May. Ate lunch at Ann's in Ballard. Delish shrimp sate! I busted my tire in a pothole and had to make a trip to REI. Which wasn't awful because we wanted to go there anyway. The city was tough to ride in at 5:00pm and we rode the sidewalk most of the way back due to the congestion. Some pedestrians are obvious to you and I almost ran over a few people.. By choice. Lol. Made it back right before they closed at 6:00pm. Easy peasy! Notes: Take some water. Take some pictures. The ride is beautiful so don't rush through. Get there before noon to give yourself some time to cruise.
Before I get started, I should mention that I never leave reviews. This is probably my first one on Yelp. These guys are just so great that I felt compelled to give them a shoutout. This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. These guys will give you their best and provide some laughs as well. Couldn't recommend them more!
The Pedro’s lever slipped only once throughout testing, though that may have been my fault because I was spaced out after changing 16 different tires. So they’re not foolproof, but they are far and away more reliable than the next closest competitor, from Park Tool, because the small, rounded tip on that one is hard to keep seated under the tire. Not impossible, but I wouldn’t choose it over Pedro’s.
Pedals are important because the serve as the contact point between the rider and the bike’s transmission. Clip-less pedals systems come in a variety of designs favoured by individual manufacturers, but the mechanics of all styles are roughly the same. Tiny adjustments in the position of the show cleat – that snaps into position on the pedal – can make a big difference to the comfort and health of the rider.
×