There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
Mini Pump:   This actually goes on the frame of your bike, as it’s a bit too big for most under-seat bags.   Coming soon, we’ll have a review from Bill of his very favorite one, but a good pump is a lifesaver.    Some people instead carry a CO2 inflator, which is faster and easier to use but does require disposable cartridges, and each time you have a flat, you’ll need at least 2 of those cartridges.  There are combined pump/inflator tools that we’ll also talk about soon.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.

Maintenance is the best prevention. “Prevention is the best medicine, and if you’re taking care of your equipment it’s super key. Bikes don’t just fail. If they’re in really good working condition and you clean them at night, and you’re religious about it, bikes are kind of like cars — they’ll start talking to you if something is getting worn or getting creaky or needs to be replaced.”
Any bike that gets ridden seriously as transportation or on long rides needs at least a basic tool/emergency kit, and the knowledge to use it, unless the rider is always in a position to call a friend with a car or a cab when their bike needs a quick fix on the road.  If you never travel more than a few miles, this can be overkill, and calling a friend or a cab may be just the ticket,  but if you want to be more self reliant, this is something you should seriously consider.  This list may sound like an awful lot of stuff to carry, but really, it only weighs a few lbs and fits in a small, under-seat bag that comes off quickly so I don’t have to leave it with the bike if theft is a concern.  If you always carry a regular rack top bag, you can also just put all this in a small nylon bag and throw it in there, but I prefer an under-seat bag.
Every expert I spoke to recommended Pedro’s Tire Levers by name. They have a wide body—a different shape than other models we tested—and that prevents breakage, but more important, the broad, flat surface area of the tip helps it stay locked under your tire. When a lever slips from under the bead of the tire, you can end up repeatedly scraping your knuckles on the spokes of the wheel, which is so annoying. Pedro’s levers are small enough to fit into a saddlebag, are sold widely in bike shops, and even come with a lifetime guarantee. If one breaks, Pedro’s will replace it.

We like, and recommend, the Crankbrothers Speedier Lever. If you have to pick only one, go with the Pedro’s, but if you want a backup or have some hard tires to unseat, Crankbrothers is a great choice. It’s only one lever (as opposed to a set of two, like the Pedro’s) and it’s longer, so we didn’t pick it over the Pedro’s for portability reasons. But it’s an excellent tool. It has a wide handle you can grip with your whole hand. Like the Pedro’s, the tip is the right size and shape to prevent slipping and stay in place, and the shape of the handle happens to protect your knuckles if you do slip. Even in situations where I didn’t need it, I liked having it because it made me feel like a pro.


Dennis Bailey has been actively involved in bike repair and maintenance for almost two decades. He has worked on bikes on bike tours in the United States, Europe, and Latin America. Keith Gates has been repairing bikes for more than 30 years and provides personalized service as the owner of A-1 Cycling, with locations in Manassas and Herndon, Virginia.
Every person who considers themselves a cycling enthusiast should know how to do at least some basic bike repairs. This is not just to satisfy an unwritten standard of being a bikehead, but because it has a lot of practical implications as well. It can make the difference between dealing with a minor issue quickly on your own or waiting a couple of days for a busy mechanic to squeeze you in. Moreover, in the long run, doing the dirty work yourself will save you a lot of money.

Modern bottom brackets use a sealed bearing type construction that keeps water and debris locked out, so they seldom go wrong. Maintenance is impossible so they need replacing when they do wear out. Older style cup bottom brackets need to be re-greased every now and again, and occasionally will need to have their bearings replaced. There are a lot more teeth on the chainring cogs than those on the rear cassette, so need changing less regularly. Cranks usually a solid one piece construction so there is not much to go wrong.
×