Do not take your Bike to Kyle's Bike Shop they handled my bike so poorly they can not work on Vintage Schwinn' and the attitude they had if it wasn't a high dollar bike don't expect good service. I had to find my own parts, had to take the bike back twice to get the wheel trued and they ruined my bike it is so scrapped up the Schwinn is gone on the side of the bike. If you care about your bike do not take it here.

Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Packed with basic tools, this compact tin rescues puncture-interrupted bike trips. Pedaling away to a picnic spot with a pal, you hear a disconcerting "pop!". Your two-wheeler is now down one wheel, and unless you've got mad unicycle skills, you need tools. Good thing you brought this handsome, compact tin. Just break out the metal tire levers and patch kit, and you're rolling along again in no time. The six-sided, dog bone-style hex wrench adjusts the most common bike screws and bolts and screws. Made in China.
There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
Modern bottom brackets use a sealed bearing type construction that keeps water and debris locked out, so they seldom go wrong. Maintenance is impossible so they need replacing when they do wear out. Older style cup bottom brackets need to be re-greased every now and again, and occasionally will need to have their bearings replaced. There are a lot more teeth on the chainring cogs than those on the rear cassette, so need changing less regularly. Cranks usually a solid one piece construction so there is not much to go wrong.
×