Road riders need lightweight, tiny tools that can fit into jersey pockets. A lot of those items are made of carbon fiber, which is lighter than aluminum. Other iconic trappings of road riding, like CO2 cartridges and spandex outfits, are also geared toward minimalism, but all of that downsizing comes at a cost. Commuters don’t have to be as concerned with weight, so unless you covet something specific, don’t spend the extra money.
Writer Peter Flax, the former editor-in-chief of Bicycling magazine, rode over 1,000 miles and tested 15 tools for our full-length guide to multi-tools, and he concluded the Topeak Mini 9 is the best for casual cyclists. It’s tiny, it’s light, it’s easier to get some leverage with than other tools that have different designs. It’s not meant for serious wrenching on your bike, but it’s good for on-the-fly adjustments.
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
It has some useful information for basic repairs... not so heavy on the maintenance side but there is some in there. The pictures and drawings are in black and white, but mostly visible. Only a few are difficult to see. However, they are in 2-dimensions and they don't show you HOW to do the thing, they only show you the general area and the part you want to manipulate. The phrasing in the instructions can be hard to follow without a good visual reference unless you're already a master bike mechanic (which you aren't if you're thinking about buying this). So, buy this for general reference and rely on Youtube for video. The two together are better than either one alone.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
To pick the right size bicycle, you want to measure your height, and specifically your inseam (inside leg), in proportion to the size of the bike frame. The inseam measurement determines the seat height, or the “stack.” Next, you must calculate the “reach,” which is the horizontal distance between the bottom of the frame and the head of the bike -- or, in layman’s terms, the distance between seat and handlebars.

If you are planning on going on a multi-day ride or just riding a long distance in a day, you should have something for first aid, just in case. Unfortunately, almost everyone who cycles frequently will go down at least once in their life. This kit can be really small and compact and can include bandages, some gauze, and a small bottle of a disinfectant.
First, carbon. You already know you don’t need it for your casual weekend pursuits, because you’re not counting ounces the way a professional road racer would. But to quote an article from Velonews, “Remember that professional athletes operate in an entirely different environment than the rest of us. They are all very close to each other in terms of fitness, and they are also all very close to being the absolute best a human being can be. In short, you’re much better off upgrading your legs and dropping body fat through proper training and diet.”
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
Modern bottom brackets use a sealed bearing type construction that keeps water and debris locked out, so they seldom go wrong. Maintenance is impossible so they need replacing when they do wear out. Older style cup bottom brackets need to be re-greased every now and again, and occasionally will need to have their bearings replaced. There are a lot more teeth on the chainring cogs than those on the rear cassette, so need changing less regularly. Cranks usually a solid one piece construction so there is not much to go wrong.
×