Some years ago, I used to live on my bike. Riding around daily through any weather condition was bound to quickly wear down on the bike over time. I like some of the stuff that you have in your toolkit. I would say zip ties are actually really convenient, because when something came loose you could go ahead and use those to fasten them down to keep on moving ahead until you had enough time to fix it or get it checked at a bike repair shop.
That’s a reality of all hand pumps—it’s really hard to get a tire up to pressure with these things. So another reason Lezyne pumps are so good is because you can actually keep pumping longer than any other brand we tested. With excruciating effort, we could get the Sport Drive HP to pump tires to 90 or 100 psi. It still wasn’t easy, but it wasn’t impossible the way it was with some other models.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Packed with basic tools, this compact tin rescues puncture-interrupted bike trips. Pedaling away to a picnic spot with a pal, you hear a disconcerting "pop!". Your two-wheeler is now down one wheel, and unless you've got mad unicycle skills, you need tools. Good thing you brought this handsome, compact tin. Just break out the metal tire levers and patch kit, and you're rolling along again in no time. The six-sided, dog bone-style hex wrench adjusts the most common bike screws and bolts and screws. Made in China.
It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.
I bicycle to and from work to save gas. I don't have a fancy bike, it's just a Schwinn mountain bike that's comfortable and can carry me plus gear but I want to be able to do my own work on it. I needed a book that was simple enough for someone new to bicycle repair and maintenance but could take me through all the upkeep my workhorse needs, and this book does just that. It's well-written and easy to follow.
There are two major types of headset- older, threaded headsets that have a quill that drops into the stem of the fork creating an interference connection, and newer threadless headsets that the stem is bolted and clamped on to. Flat handle bars are preferred by off road cyclists who can ride in a more upright postion whilst still having the controls at their fingertips, whereas drop handlebars offer more cycling positions and are favoured by road cyclists who typically spend more time in the saddle. The controls attached to the different styles of bar are operated and maintained in different ways.
×