Don’t rely on others. “People need to recognize that now there are different cassette sizes, so there are different chains depending on what gear you have. A lot of people are like, ‘Oh my friend is always prepared they always have the stuff, I’m not going to bring anything.’ All of the stuff now is very bike-specific, and you have to have your own package of stuff.”
Inside Student Union across from College Optical, the UCF Bike Repair Service is provided for students with bike problems. Students may come, free of charge, and have their bikes repaired with quality service by our Bike Repair Team. Service include: Inflate tires, change tubes, brake adjustments, tighten crankset, loose handlebars, adjust gears, and brake cable installation. Bikes can also be reserved here as part of the Bike Share program.
Main types of bicycles are road, mountain, commuter/comfort and fitness bikes. There are more specific types and other names for bike types within that, such as urban bikes (same as commuter bikes), cruiser bikes, dual-sport bikes, hybrid bikes, fixed-gear bikes, cyclo-cross bikes, adventure road bikes (aka all-road bikes, gravel bikes), road bikes, touring bikes and specialty bikes, like BMX.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
As you mentioned, it is surprising how often you can get multiple flat tires on while riding, particularly on longer sprints. The tip about bringing a patch kit in your bike repair kit can be incredibly helpful if you’ve already had one flat tire. I agree that all you listed seems like an awful lot to carry, but it’s always better to be safe than sorry, isn’t it?
It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.
This is a very basic book and unnecessarily repetitive in sections. It does introduce the reader to the basic nomenclature of bicycles and this is helpful when conversing with others. Unfortunately the repetitive sections were not replaced with chapters on 3 Speed in hub gear drives, or coaster breaks, or a chapter on Adult Tricycles and Tandems and E-Bikes.
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
A wrench that fits the hub nuts: If your bike has quick release front and rear wheels, you don’t need this, but if you have an internal hub on the back, such as the NuVinci, a wrench that fits is a great idea. 99% of the time, this is a 15mm wrench, but you should check your bike. A 6 inch adjustable wrench can also work, but it will be heavier, and when using an adjustable wrench, you do need to take more care to not round over the nuts. A fixed wrench is the best choice. Some multi-tools have a 15 mm wrench built in, but again, if you have limited hand strength, something with more leverage is a great idea.
Yes, bicycle shops generally provide repair services. A typical list of offered services includes regular service/adjustment (including safety check; and brake, drivetrain, and tire inspection); premium, and annual service, which is a more extensive tune-up. More specific repairs include drivetrain tune-up, brake system tune-up, flat tire fixes, brake repairs, cleaning and touching up the bike frame.
On a very sunny Saturday I had a rear spoke break - you can imagine that no shop was willing to promise a quick repair! I was so fortunate to find this shop and will come back - Andy not only told me to come down and he'd get it fixed, he had his assistant work with another couple while he measured, cut to the right size, installed and trued the wheel while I waited! It was awesome, and the whole place had a great feel and good people. Best of all he charged a very fair $20 for all that work - I would have paid a premium for the quick service! After experiencing lots of attitude at other shops and poor service, this was a real find. I hope you will check them out, they have a great selection of bikes and accessories too! Good people and good craftsmanship should be rewarded.
There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
In spite of seat bags’ diminutive size, a lot of people really, really want them to accommodate more stuff. If that’s you, the medium and large seat bag (but not the small) have an extendable gill at the bottom, which you can see in the image up top. It zips open to create more room. With it unzipped, we could cram a wallet, keys, and phone inside the medium as well.
Return: Bicycle and lock must be returned by the end of the loan period. User will be charged a $10.00/day late fee. After 10 business days user will be charged the full cost of the bicycle ($350) and rented equipment ($50 for lock and/or key). Failure to return bicycle, helmet and lock will subject user to legal liability of $400.00, as well as having student account placed on hold.