But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
There are two major types of headset- older, threaded headsets that have a quill that drops into the stem of the fork creating an interference connection, and newer threadless headsets that the stem is bolted and clamped on to. Flat handle bars are preferred by off road cyclists who can ride in a more upright postion whilst still having the controls at their fingertips, whereas drop handlebars offer more cycling positions and are favoured by road cyclists who typically spend more time in the saddle. The controls attached to the different styles of bar are operated and maintained in different ways.
For the budding mechanic: A good pocket sized repair guide. One good option is the “Pocket Guide to Emergency Bicycle Repair” by Ron Cordes and Eric Grove. It’s only 3.5×4.5 inches and a half inch thick. I don’t carry this myself, but for someone who’s new to this whole bike repair business, it’s really helpful to have. A future blog post will cover this book in detail.
Don’t rely on others. “People need to recognize that now there are different cassette sizes, so there are different chains depending on what gear you have. A lot of people are like, ‘Oh my friend is always prepared they always have the stuff, I’m not going to bring anything.’ All of the stuff now is very bike-specific, and you have to have your own package of stuff.”
Mountain bikers are in different world of repair entirely, one that borders on the comedic absurd. It includes large pumps designed to fill up big, fat tires that squish over things, and a medley of assorted slimes meant to be injected into tubes or tires. In that world, the number of days it takes you to fix your tire and return from the wilderness is a badge of courage—bonus points if you’re bleeding—and we’re guessing that’s not what you’re going for next time you set out for groceries.
High quality bike repair stand features with 360° swivel head and adjustable height. It is convenient to use our bicycle repair stand no matter you are sitting or standing. Covered by plastic, the clamp keeps your bike in place and protects the paint of your bike nicely. Made from sturdy metal, this bike work stand can holds up to 30kg/66 lb. It is a perfect choice for bike enthusiasts, bike clubs, bike shops and bike repair shops.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Good bike repair stand. I can't say "great," because it arrived with some small plastic pieces broken. These are small pieces that go between the legs and the supports for the legs to act as a sort of buffer to prevent metal to metal scraping. They are just too fragile, it seems. 3 out of 4 legs had these broken upon arrival. However, these are really only "nice" to haves, not need to haves, and they don't really detract from using the stand in any way. Once you have the stand set up, you don't worry about these at all. The main clamp holds the bike well, if you take care to balance the bike properly. The bike may tilt in the stand if you don't balance it - there is a weight limit to the clamp. I like the included tool tray, but I wish it was more adjustable in height (it is essentially fixed in one position). And the tray could be larger. Otherwise, I am quite happy with this stand. I have worked on several bikes using it, and assembled one out of the box. It makes the job of doing things like adjusting brakes and indexing derailleurs so much easier. The price of this stand is excellent considering the quality.
Change and a $20 bill: In case your cell phone’s battery dies, it’s nice to still be able to use a payphone if you need to. Also, the $20 is a great thing to have in case you lose your wallet or have some other mishap. I’d rather be able to sit in a coffee shop or fast food restaurant when it starts raining while I’m waiting for my friend or cab ride, and a hot cup of tea or coffee or the beverage of your choice and a snack makes it all the more pleasant. Just try to remember, this is for emergencies, and if you use it, replace it ASAP!