Inside Student Union across from College Optical, the UCF Bike Repair Service is provided for students with bike problems. Students may come, free of charge, and have their bikes repaired with quality service by our Bike Repair Team. Service include: Inflate tires, change tubes, brake adjustments, tighten crankset, loose handlebars, adjust gears, and brake cable installation. Bikes can also be reserved here as part of the Bike Share program.
These are some great ideas, especially the simple ones like bringing a garbage bag. That’s something so easy and cheap that it’s easy to forget entirely, but as you say, it can make a huge difference in the right circumstances. It’s also good that you discuss some minor bike repairs. That’s another thing that can salvage or destroy your ride. You want to be as prepared as possible for the best possible experience.

In addition to the Rema patches, put a new tire tube in your kit. The best method for dealing with a flat roadside is to swap out the tube and save the task of patching for later. If you’re not sure what size your tires are, it’s printed on the sidewall of the tire. This inner-tube buying guide has some photos of where to look. What brand is almost irrelevant as many tubes get manufactured in the same place, so whatever your local shop has behind the counter for under $10 will work fine. The only reason to spend more would be to save weight.


It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
If you have just a short time in Seattle there is only one way to see the city. Walk at 2.5 miles an hour? I don't think so. Take buses and trams that you have to wait for and that might not even get you where you need to go? No way Jose. Drive your car? Hahahaha get outta here, don't even talk to me. But what about a BICYCLE??? Now that's the ticket. The Bicycle Repair Shop does rentals by the hour or by the day. They have reasonable rates. They have solid, lightweight hybrid bikes so you can tackle train tracks and brick streets and hills. They also have road bikes for the more experienced. You can reserve online in advance. You get a helmet and a lock with your rental. The staff in the shop are friendly and will suggest routes and point out hills if you're new to the area. And believe me these hills are no joke! I had a great time in Seattle and it's all thanks to this business. Next time I visit I am definitely doing this again.
Friction gear systems are a lot simpler to adjust, because the movement of the derailer cable can be modulated as you ride, every time you change the gear- they require less cycle maintenance. Modern index shifting systems are a little more complicated because each ‘click’ must release the exact right amount of cable to allow the derailer to move the correct distance to move the chain from one gear to another. Setting up and adjusting a derailer is not difficult and requires only basic tools, but there is a methodical procedure to follow.
×