This gentleman is a true professional!! He is an ex-Marine and I will tell you that he represents them well. He is honest, knowledgeable and extremely reasonable. He repaired my son's bike while I waited and went over the whole bike and made the required adjustments replaced an inner tube and all for 20 dollars!!All the kids in the area pass by and call him by his first name. I will recommend him to everyone I know since there are very little of them out there!!
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Don’t rely on others. “People need to recognize that now there are different cassette sizes, so there are different chains depending on what gear you have. A lot of people are like, ‘Oh my friend is always prepared they always have the stuff, I’m not going to bring anything.’ All of the stuff now is very bike-specific, and you have to have your own package of stuff.”
Riding the bus with three infants in a stroller is no easy task, especially when you realize you have a flat tire as soon as you step foot on the pavement of 2nd and University. Luckily, I found The Bicycle Repair Shop. Andy happily filled my tire with air, and when it was flat again an hour later, found a replacement tube in minutes. He changed the tire with the babies still in the stroller! This was such an amazing experience that totally made a fun day possible for us! Thank you, Andy!
Road riders need lightweight, tiny tools that can fit into jersey pockets. A lot of those items are made of carbon fiber, which is lighter than aluminum. Other iconic trappings of road riding, like CO2 cartridges and spandex outfits, are also geared toward minimalism, but all of that downsizing comes at a cost. Commuters don’t have to be as concerned with weight, so unless you covet something specific, don’t spend the extra money.
Spare tube: Sometimes, a tube is just too damaged to be patched, or has had a failure such as the valve stem breaking off which isn’t something that can be patched. To save weight and space, I usually keep a lightweight version of the right size tube for my bike. Since one of the first things I do with most bikes that I own is switch them over to heavy-duty thorn resistant tubes, I just take one of the originals and put that in the toolkit.
This is a very basic book and unnecessarily repetitive in sections. It does introduce the reader to the basic nomenclature of bicycles and this is helpful when conversing with others. Unfortunately the repetitive sections were not replaced with chapters on 3 Speed in hub gear drives, or coaster breaks, or a chapter on Adult Tricycles and Tandems and E-Bikes.
That’s a reality of all hand pumps—it’s really hard to get a tire up to pressure with these things. So another reason Lezyne pumps are so good is because you can actually keep pumping longer than any other brand we tested. With excruciating effort, we could get the Sport Drive HP to pump tires to 90 or 100 psi. It still wasn’t easy, but it wasn’t impossible the way it was with some other models.
Yes, bicycle shops generally provide repair services. A typical list of offered services includes regular service/adjustment (including safety check; and brake, drivetrain, and tire inspection); premium, and annual service, which is a more extensive tune-up. More specific repairs include drivetrain tune-up, brake system tune-up, flat tire fixes, brake repairs, cleaning and touching up the bike frame.
Keychain style flashlight or headlamp, LED type, not incandescent: The keychain style is tiny and lightweight, the headlamp style is a bit bulkier but easier to use. You can get these for a couple of bucks or less at the local big box hardware store. The LED ones are lighter, more durable and last considerably longer. Very useful if you need to make a repair after dark! I keep a keychain style one as a backup as I normally have a headlamp in my backpack.
More than any other tool in the kit, a reliable lever makes changing a tire easier, especially if you have road bike tires, which are difficult to remove. However, throughout testing, levers seemed to be the one item more prone to failure and poor design than anything else. For example, I found a random orange lever floating around my basement and I threw it in the test pool for fun—it seemed solid enough … until I began prying at the rim of a tire. It bent directly in half, slowly and smoothly, like taffy, and then was boomerang shaped forevermore.
As you mentioned, it is surprising how often you can get multiple flat tires on while riding, particularly on longer sprints. The tip about bringing a patch kit in your bike repair kit can be incredibly helpful if you’ve already had one flat tire. I agree that all you listed seems like an awful lot to carry, but it’s always better to be safe than sorry, isn’t it?
This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement.
We spoke to a broad spectrum of cyclists—from a pro racer to a bike messenger turned mechanic to a touring cyclist who has logged thousands of miles throughout Europe—to find out what items they find indispensable. We sorted through 40 tire levers, almost 30 different kinds of patches, 120 different hand pumps, and 57 seat bags before we narrowed our choices for testing. And then we changed and patched tires more than 50 times, using four different bikes, five different wheels, six different tires, and almost 10 different sizes of tubes. After 96 hours of combined testing, we agree these essentials are some of the best you can buy.
Friction gear systems are a lot simpler to adjust, because the movement of the derailer cable can be modulated as you ride, every time you change the gear- they require less cycle maintenance. Modern index shifting systems are a little more complicated because each ‘click’ must release the exact right amount of cable to allow the derailer to move the correct distance to move the chain from one gear to another. Setting up and adjusting a derailer is not difficult and requires only basic tools, but there is a methodical procedure to follow.