We're Arizona's top rated and 5 times running "America's Best" Rated Bike Shop by the NBDA. From mountain bikes, kids, comfort, fitness and road bikes we sell and service them all! Are E-bikes your thing? Our Gilbert location Is our hub for electric bike sales and service. Swing by and see us... Family owned and operated by Brandee and Al since 2001.
These folks took me in right away, diagnosed and fixed my stripped handle bar clamps and had me on my way to work in about 15 minutes. Friendly, straightforward, understands the rider's objectives (in my case, how do I get home from work). Not to mention, the fee was reasonable. I have been in many bike repair places in my 6 decades. This is the best.
First, carbon. You already know you don’t need it for your casual weekend pursuits, because you’re not counting ounces the way a professional road racer would. But to quote an article from Velonews, “Remember that professional athletes operate in an entirely different environment than the rest of us. They are all very close to each other in terms of fitness, and they are also all very close to being the absolute best a human being can be. In short, you’re much better off upgrading your legs and dropping body fat through proper training and diet.”
I brought my bike into Kyle's shop to fix the noise in my rear wheel. The mechanic suggested that I need to overhauled the rear hub for $30. The next day the noise came back even worst. I brought it back to the shop and they said it was the freewheel driver not the hub that needed to be work on and it would cost me extra $30 to overhauled it again plus the part to fix it. At this point I walked out of the shop and took my bike to David's world. The mechanic at David's world took a quick look at the rear hub and indicated that the axle was put back too tight when Kyle's mechanics were working on it and further identify the issue. I ended up paying David's world the $30 plus part to fix my bike, but the major different is that David's World has 30 Days services warranty claim. If you have any issue with your bike within the 30 days the service was performed you can bring it back and they will fix it no question ask.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Pedals are important because the serve as the contact point between the rider and the bike’s transmission. Clip-less pedals systems come in a variety of designs favoured by individual manufacturers, but the mechanics of all styles are roughly the same. Tiny adjustments in the position of the show cleat – that snaps into position on the pedal – can make a big difference to the comfort and health of the rider.