I brought my bike into Kyle's shop to fix the noise in my rear wheel. The mechanic suggested that I need to overhauled the rear hub for $30. The next day the noise came back even worst. I brought it back to the shop and they said it was the freewheel driver not the hub that needed to be work on and it would cost me extra $30 to overhauled it again plus the part to fix it. At this point I walked out of the shop and took my bike to David's world. The mechanic at David's world took a quick look at the rear hub and indicated that the axle was put back too tight when Kyle's mechanics were working on it and further identify the issue. I ended up paying David's world the $30 plus part to fix my bike, but the major different is that David's World has 30 Days services warranty claim. If you have any issue with your bike within the 30 days the service was performed you can bring it back and they will fix it no question ask.

Whether you ride a single, 7, or 10 speed bike or anything in between, you will need a slightly different chain. The major difference is that they come in varying widths to accomodate the different spaces between the gears, but quality of construction is also a factor in choosing a chain. Inspecing the chain should be a part of your regular cycle maintenance procedure- It’s important to keep a chain well lubricated, but oil will also attract dirt and so different oils for specific riding conditions are available. Remember to clean your chain regularly to get the longest life out of it and the gears.

Let me go ahead and get the bad stuff out of the way. First of all, this stand is NOT the same level of quality as something you would find in a bicycle shop being used for the shop's repairs. it's quite a bit more flimsy, and the grip likes to rotate if you don't get the bike's center of gravity just right. The tool tray is also made out of a rather cheap plastic that can break easily at the rim. That being said, this stand is perfect for home users and makes mundane tasks like fixing a flat or cleaning the chain much easier. It easily holds my Raleigh Merit 3, and I don't worry about the thing falling even if the grip tilts a bit. The stand significantly shortened the time I needed to change an inner tube on my bicycle, and made me less worried about damaging something on the bike by jury-rigging a stand out of whatever I had lying around.
Bikes have remained popular since time in memorial. It’s fun being a rider. Their existence brings about the need to preserve their smooth riding. A bicycle like any mechanically driven tool requires regular service as they are prone to artificial failure. To ensure an outstanding service, the appropriate toolkit should be employed. It may not be easy to obtain the best toolkit, but with us, you are guaranteed quality and efficient toolkits.

Mini Pump:   This actually goes on the frame of your bike, as it’s a bit too big for most under-seat bags.   Coming soon, we’ll have a review from Bill of his very favorite one, but a good pump is a lifesaver.    Some people instead carry a CO2 inflator, which is faster and easier to use but does require disposable cartridges, and each time you have a flat, you’ll need at least 2 of those cartridges.  There are combined pump/inflator tools that we’ll also talk about soon.
It includes nine tools: seven hex bolts, one torx bolt (the star-shaped one), and a Phillips screwdriver (also the star-shaped one). Like Peter says in our guide, if you have a newer mountain bike or road bike it pays to take a quick look at what types of tools you need, as torx bolts are becoming more common. And a quick glance at the bottom of your shoes or derailleur bolts will confirm if a Phillips head is the right choice.
Owning a bicycle is a good idea, but taking care of it yearns for an experts’ piece of mind. You should not worry too much about taking your bicycle to a mechanic when you can handle the repairing on your own. It will rather save you the cost of every moment you get into a problem. Grab a pick of one of the toolkits from the above review. I assure you that, absolutely no day will you seek a mechanic for service.

It has some useful information for basic repairs... not so heavy on the maintenance side but there is some in there. The pictures and drawings are in black and white, but mostly visible. Only a few are difficult to see. However, they are in 2-dimensions and they don't show you HOW to do the thing, they only show you the general area and the part you want to manipulate. The phrasing in the instructions can be hard to follow without a good visual reference unless you're already a master bike mechanic (which you aren't if you're thinking about buying this). So, buy this for general reference and rely on Youtube for video. The two together are better than either one alone.
Now you might be wondering: “I’m carrying a tube; why carry patches at all?” As insurance for the unforeseeable. Wirecutter senior editor Christine Ryan admits she didn’t use to pack them, but said, “I’ve regretted that decision when I’ve had a flat on a ride, used my spare tube, and then, half an hour later, had a second flat. Also, lots of people aren’t very good at figuring out—or don’t take the time to figure out—what caused their flat and remove the cause: thorn, eensy bit of glass, whatever. Then they promptly have a second flat, and everyone else laughs at them.”
Bike Radar gives the Pedro’s levers 4.55 out of five stars and claims they’re the “best out there.” (Can we pause to admire the extra five hundredths of a star the site chose to award it? Very specific.) Aaron Gulley, writing for Outside, states, “I can’t count the number of times I’ve snapped cheap plastic sticks, shredded my hand in the process, stomped around cursing in pain for 10 minutes, and then, insult to injury, been tool-less and unable to get my tire off anyway. That will never happen with Pedro’s.”

But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).

It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.

Inside Student Union across from College Optical, the UCF Bike Repair Service is provided for students with bike problems. Students may come, free of charge, and have their bikes repaired with quality service by our Bike Repair Team. Service include: Inflate tires, change tubes, brake adjustments, tighten crankset, loose handlebars, adjust gears, and brake cable installation. Bikes can also be reserved here as part of the Bike Share program.
×