Next to everything else that might go wrong with a bicycle on an extended ride, a flat is a relatively minor issue that can be easily repaired trailside, if the right tools are at hand. If they aren’t, a quick fix can turn into a long walk. Well-prepared riders will perform a tune-up regularly and clean their bikes after every ride. For the less-diligent, a well-stocked repair kit will suffice.
But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
Good bike repair stand. I can't say "great," because it arrived with some small plastic pieces broken. These are small pieces that go between the legs and the supports for the legs to act as a sort of buffer to prevent metal to metal scraping. They are just too fragile, it seems. 3 out of 4 legs had these broken upon arrival. However, these are really only "nice" to haves, not need to haves, and they don't really detract from using the stand in any way. Once you have the stand set up, you don't worry about these at all. The main clamp holds the bike well, if you take care to balance the bike properly. The bike may tilt in the stand if you don't balance it - there is a weight limit to the clamp. I like the included tool tray, but I wish it was more adjustable in height (it is essentially fixed in one position). And the tray could be larger. Otherwise, I am quite happy with this stand. I have worked on several bikes using it, and assembled one out of the box. It makes the job of doing things like adjusting brakes and indexing derailleurs so much easier. The price of this stand is excellent considering the quality.
Some years ago, I used to live on my bike. Riding around daily through any weather condition was bound to quickly wear down on the bike over time. I like some of the stuff that you have in your toolkit. I would say zip ties are actually really convenient, because when something came loose you could go ahead and use those to fasten them down to keep on moving ahead until you had enough time to fix it or get it checked at a bike repair shop.
Packed with basic tools, this compact tin rescues puncture-interrupted bike trips. Pedaling away to a picnic spot with a pal, you hear a disconcerting "pop!". Your two-wheeler is now down one wheel, and unless you've got mad unicycle skills, you need tools. Good thing you brought this handsome, compact tin. Just break out the metal tire levers and patch kit, and you're rolling along again in no time. The six-sided, dog bone-style hex wrench adjusts the most common bike screws and bolts and screws. Made in China.
Let me go ahead and get the bad stuff out of the way. First of all, this stand is NOT the same level of quality as something you would find in a bicycle shop being used for the shop's repairs. it's quite a bit more flimsy, and the grip likes to rotate if you don't get the bike's center of gravity just right. The tool tray is also made out of a rather cheap plastic that can break easily at the rim. That being said, this stand is perfect for home users and makes mundane tasks like fixing a flat or cleaning the chain much easier. It easily holds my Raleigh Merit 3, and I don't worry about the thing falling even if the grip tilts a bit. The stand significantly shortened the time I needed to change an inner tube on my bicycle, and made me less worried about damaging something on the bike by jury-rigging a stand out of whatever I had lying around.
Nice, helpful, friendly. Central location. Good bikes (I had two over two days.) Bikes had a water bottle cage (some places don't do that!) Provided helmets if needed (I didn't) and a one-sided pannier containing a decently strong but not super-heavy cable lock and a patch kit. Only quibbles: 1) The owner helping me with getting my bikes seemed to 'drop me' for too long when someone else walked in. He should have said to them, after asking what they were in for, that 'I'll be with you as soon as I'm finished with this person.' So I had to wait a little longer than desired, but not bad. 2) On my second day, the pannier bag fell off and got lost after I stopped for lunch, which required locking up the bike somewhere, so I took the bag into restaurant and re-attached it using the two velcro straps on the rear rack. I've used many panniers before, thought I did it correctly. But apparently I did not. So I paid $55 (cost) to replace everything in bag and bag. In hindsight, I wished I'd put a bungee around bag straps to really secure it to bike. PROBABLY MY FAULT. 3) Bring a second lock to lock quick-release front wheel, as decently strong but not super-heavy cable lock isn't long enough for both wheels and frame.I had a second cable lock.
Riding the bus with three infants in a stroller is no easy task, especially when you realize you have a flat tire as soon as you step foot on the pavement of 2nd and University. Luckily, I found The Bicycle Repair Shop. Andy happily filled my tire with air, and when it was flat again an hour later, found a replacement tube in minutes. He changed the tire with the babies still in the stroller! This was such an amazing experience that totally made a fun day possible for us! Thank you, Andy!
Bike Radar gives the Pedro’s levers 4.55 out of five stars and claims they’re the “best out there.” (Can we pause to admire the extra five hundredths of a star the site chose to award it? Very specific.) Aaron Gulley, writing for Outside, states, “I can’t count the number of times I’ve snapped cheap plastic sticks, shredded my hand in the process, stomped around cursing in pain for 10 minutes, and then, insult to injury, been tool-less and unable to get my tire off anyway. That will never happen with Pedro’s.”
It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.
A wrench that fits the hub nuts: If your bike has quick release front and rear wheels, you don’t need this, but if you have an internal hub on the back, such as the NuVinci, a wrench that fits is a great idea. 99% of the time, this is a 15mm wrench, but you should check your bike. A 6 inch adjustable wrench can also work, but it will be heavier, and when using an adjustable wrench, you do need to take more care to not round over the nuts. A fixed wrench is the best choice. Some multi-tools have a 15 mm wrench built in, but again, if you have limited hand strength, something with more leverage is a great idea.
A pair of disposable latex gloves: Not absolutely necessary, but good for keeping grease and grime off your hands during a repair. Also, nice to have in an emergency when it starts raining and the temperature drops 20 degrees and you don’t have a pair of regular gloves. Just keeping your hands dry and the wind from directly blowing on them makes a huge difference in comfort.
Based on what we found, we chose the most relevant items and used them all. To test patches, I repaired holes using four different types of patches, from Novara (REI’s now-discontinued house brand), Park Tool, and Rema. Patching a tube isn’t hard but there are a few tricks, and the key was attention to detail and patience. I was extremely diligent in following proper patch procedure, which includes a thorough sanding of the entire area to be patched (for max stickiness) and properly letting the vulcanizer dry on both surfaces before applying. For the peel-and-stick patches, I went so far as to prep the area with canned air to ensure as tight a seal as we could possibly muster.
We rented a tandem bike from here for an hour, and they were super chill! We dropped by on a Sunday and decided to go eat first; Andy, one of the owners, was awesome about holding the bike for us while we went to eat before renting. We enjoyed our ride for just over an hr, but Andy was also super relaxed about our return time and only charged us for an hour. We had a fantastic time and would definitely recommend renting bikes from here!
Maintenance is the best prevention. “Prevention is the best medicine, and if you’re taking care of your equipment it’s super key. Bikes don’t just fail. If they’re in really good working condition and you clean them at night, and you’re religious about it, bikes are kind of like cars — they’ll start talking to you if something is getting worn or getting creaky or needs to be replaced.”
Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.
Basically, you’re stuck with toggling between systems for the advantage of a few pumps, and it doesn’t seem worth it. In the original iteration of this guide, I tested 12 pumps and inflated three different tires completely full to their psi rating, and measured how many pumps it took. Yasuda did similarly for his revamped full-length exploration. That’s 36 tires, and I can guarantee there is no difference between 50 pumps and 100—it’s all terrible.
There are two major types of headset- older, threaded headsets that have a quill that drops into the stem of the fork creating an interference connection, and newer threadless headsets that the stem is bolted and clamped on to. Flat handle bars are preferred by off road cyclists who can ride in a more upright postion whilst still having the controls at their fingertips, whereas drop handlebars offer more cycling positions and are favoured by road cyclists who typically spend more time in the saddle. The controls attached to the different styles of bar are operated and maintained in different ways.