Any bike that gets ridden seriously as transportation or on long rides needs at least a basic tool/emergency kit, and the knowledge to use it, unless the rider is always in a position to call a friend with a car or a cab when their bike needs a quick fix on the road.  If you never travel more than a few miles, this can be overkill, and calling a friend or a cab may be just the ticket,  but if you want to be more self reliant, this is something you should seriously consider.  This list may sound like an awful lot of stuff to carry, but really, it only weighs a few lbs and fits in a small, under-seat bag that comes off quickly so I don’t have to leave it with the bike if theft is a concern.  If you always carry a regular rack top bag, you can also just put all this in a small nylon bag and throw it in there, but I prefer an under-seat bag.
A good patch will stick to your tube enough to keep air from leaking out. A great patch will act like a second skin and actually strengthen the tube where it’s applied, flexing and stretching with the tire. After 36 hours of testing, our official endorsement goes to the Rema TT 02 Touring Repair Kit. Its patches do everything other patches do, just better. The edge of the patch is also ruffled, which provides more edge surface area to bond—that’s a good thing.
This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. 

I brought my bike into Kyle's shop to fix the noise in my rear wheel. The mechanic suggested that I need to overhauled the rear hub for $30. The next day the noise came back even worst. I brought it back to the shop and they said it was the freewheel driver not the hub that needed to be work on and it would cost me extra $30 to overhauled it again plus the part to fix it. At this point I walked out of the shop and took my bike to David's world. The mechanic at David's world took a quick look at the rear hub and indicated that the axle was put back too tight when Kyle's mechanics were working on it and further identify the issue. I ended up paying David's world the $30 plus part to fix my bike, but the major different is that David's World has 30 Days services warranty claim. If you have any issue with your bike within the 30 days the service was performed you can bring it back and they will fix it no question ask.
I own the Lezyne CNC Chain Rod, which I’m a big fan of (yes, I know I’m partial to Lezyne here–they’re a local-to-me, San Luis Obispo company and they sponsored my collegiate team, so I got tons of gear) and it costs right around $30. But the truth is that even the cheapest of chain whips will likely do the job. In fact, I’ve found a dude who knows his stuff and shows you how to make this tool all by yourself. I would even go so far as to say that you probably have enough materials laying about your garage (if not, try your parents’ garage ? ) to put this together without spending anything. Check out the video below:
Want to be your own grease monkey? This plain-English guidegives you expert tips for keeping your bicycle in great conditionand handling most repairs by yourself. You'll also see how toextend the life of your bike, increase your riding comfort, andimprove safety through routine maintenance. No matter the make orsize of bicycle, this hands-on resource has all the tips youneed!
We like, and recommend, the Crankbrothers Speedier Lever. If you have to pick only one, go with the Pedro’s, but if you want a backup or have some hard tires to unseat, Crankbrothers is a great choice. It’s only one lever (as opposed to a set of two, like the Pedro’s) and it’s longer, so we didn’t pick it over the Pedro’s for portability reasons. But it’s an excellent tool. It has a wide handle you can grip with your whole hand. Like the Pedro’s, the tip is the right size and shape to prevent slipping and stay in place, and the shape of the handle happens to protect your knuckles if you do slip. Even in situations where I didn’t need it, I liked having it because it made me feel like a pro.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Basically, you’re stuck with toggling between systems for the advantage of a few pumps, and it doesn’t seem worth it. In the original iteration of this guide, I tested 12 pumps and inflated three different tires completely full to their psi rating, and measured how many pumps it took. Yasuda did similarly for his revamped full-length exploration. That’s 36 tires, and I can guarantee there is no difference between 50 pumps and 100—it’s all terrible.

If you own a bike, you need a flat-fixing kit. It’s really that simple. Sure, maybe you’ll get lucky and get a flat close to a shop, or the buses will be running on time for once, but even with all that going for you, getting stranded across town will cost you time, money, and precious sanity. You can put together a great kit in less time than it takes to read this guide.
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
Basic first aid supplies:  A few bandages of varying sizes.   6 Aspirin, or other OTC painkiller of choice.   A few alcohol pads in sealed foil packs, useful for cleaning grease off grease and grit off of the bike, and also cleaning cuts on yourself if you take a spill.  1 day supply of any prescription drugs you need to take regularly.   Wrap these up in tinfoil and tuck away.   It might just save your day.
Broadly speaking there are two major wheel sizes – 700c for road bikes and 26 inch off-road wheels. However there are a whole variety of older, less common wheel sizes and of course fold up bikes have much smaller wheels altogether. Repairing a puncture is not an emergency! It’s a basic procedure that every cyclist should be able to to perform, but doing it correctly involves more steps than many people realise. Wheel building is often seen as the most artful skill in bicycle maintenance, and separates the professionals from the amateurs but that doesn’t mean you should consider it out of reach. Truing a slightly misaligned wheel is a cycle maintenance job that almost any cyclist can perform.
×