Otherwise, this tool should serve the average commuter well. Specifically, we think you’ll find the size 4, 5, and 6 hex keys, extremely common sizes in bicycles, very helpful. They’ll adjust seat-post heights or let you remove the saddle entirely, or tighten a loose stem that’s always rattling apart. The Phillips head will tighten loose bolts on shoe cleats or the rear derailleur. The most common use for the torx would be adjusting disc brakes if you have ’em.
We offer several bicycle repair packages, or individual services in the case that you don’t need a full “tune-up”. Whether it’s a small brake adjustment or a complete bike overhaul, we’re happy to help. Our highly experienced staff is here to answer any questions you may have and will help get you and your bike back on the road as quickly as possible.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Owning a bicycle is a good idea, but taking care of it yearns for an experts’ piece of mind. You should not worry too much about taking your bicycle to a mechanic when you can handle the repairing on your own. It will rather save you the cost of every moment you get into a problem. Grab a pick of one of the toolkits from the above review. I assure you that, absolutely no day will you seek a mechanic for service.
Let me go ahead and get the bad stuff out of the way. First of all, this stand is NOT the same level of quality as something you would find in a bicycle shop being used for the shop's repairs. it's quite a bit more flimsy, and the grip likes to rotate if you don't get the bike's center of gravity just right. The tool tray is also made out of a rather cheap plastic that can break easily at the rim. That being said, this stand is perfect for home users and makes mundane tasks like fixing a flat or cleaning the chain much easier. It easily holds my Raleigh Merit 3, and I don't worry about the thing falling even if the grip tilts a bit. The stand significantly shortened the time I needed to change an inner tube on my bicycle, and made me less worried about damaging something on the bike by jury-rigging a stand out of whatever I had lying around.
I own the Lezyne CNC Chain Rod, which I’m a big fan of (yes, I know I’m partial to Lezyne here–they’re a local-to-me, San Luis Obispo company and they sponsored my collegiate team, so I got tons of gear) and it costs right around $30. But the truth is that even the cheapest of chain whips will likely do the job. In fact, I’ve found a dude who knows his stuff and shows you how to make this tool all by yourself. I would even go so far as to say that you probably have enough materials laying about your garage (if not, try your parents’ garage ? ) to put this together without spending anything. Check out the video below:
That’s a reality of all hand pumps—it’s really hard to get a tire up to pressure with these things. So another reason Lezyne pumps are so good is because you can actually keep pumping longer than any other brand we tested. With excruciating effort, we could get the Sport Drive HP to pump tires to 90 or 100 psi. It still wasn’t easy, but it wasn’t impossible the way it was with some other models.
Spare tube: Sometimes, a tube is just too damaged to be patched, or has had a failure such as the valve stem breaking off which isn’t something that can be patched. To save weight and space, I usually keep a lightweight version of the right size tube for my bike. Since one of the first things I do with most bikes that I own is switch them over to heavy-duty thorn resistant tubes, I just take one of the originals and put that in the toolkit.
A plastic garbage bag, or $2 disposable poncho: Just in case of an unexpected downpour or getting caught out after dark. More than once, I’ve gone for a ride on a beautiful day with a perfect forecast, not taken a jacket and had the weather go south on me. Being able to cover up can mean the difference between just mild discomfort or a freezing cold, shivering ride home!
The Knights Helping Knights Pantry is a student driven program at the University of Central Florida with the goal of assisting students through financially tough times. Donations that are either brought to the Pantry or are left in one of our 15 drop boxes on campus are provided by faculty, staff and students. Student organizations, departments and individuals on campus also organize food drives that benefit the Pantry.