Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.


It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.

​High quality bike repair stand features with 360° swivel head and adjustable height. It is convenient to use our bicycle repair stand no matter you are sitting or standing. Covered by plastic, the clamp keeps your bike in place and protects the paint of your bike nicely. Made from sturdy metal, this bike work stand can holds up to 30kg/66 lb. It is a perfect choice for bike enthusiasts, bike clubs, bike shops and bike repair shops.

Return: Bicycle and lock must be returned by the end of the loan period. User will be charged a $10.00/day late fee. After 10 business days user will be charged the full cost of the bicycle ($350) and rented equipment ($50 for lock and/or key). Failure to return bicycle, helmet and lock will subject user to legal liability of $400.00, as well as having student account placed on hold.


​High quality bike repair stand features with 360° swivel head and adjustable height. It is convenient to use our bicycle repair stand no matter you are sitting or standing. Covered by plastic, the clamp keeps your bike in place and protects the paint of your bike nicely. Made from sturdy metal, this bike work stand can holds up to 30kg/66 lb. It is a perfect choice for bike enthusiasts, bike clubs, bike shops and bike repair shops.
Keychain style flashlight or headlamp, LED type, not incandescent:   The keychain style is tiny and lightweight, the headlamp style is a bit bulkier but easier to use.    You can get these for a couple of bucks or less at the local big box hardware store.  The LED ones are lighter, more durable and last considerably longer.   Very useful if you need to make a repair after dark!  I keep a keychain style one as a backup as I normally have a headlamp in my backpack.
There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
If you own a bike, you need a flat-fixing kit. It’s really that simple. Sure, maybe you’ll get lucky and get a flat close to a shop, or the buses will be running on time for once, but even with all that going for you, getting stranded across town will cost you time, money, and precious sanity. You can put together a great kit in less time than it takes to read this guide.
If you have just a short time in Seattle there is only one way to see the city. Walk at 2.5 miles an hour? I don't think so. Take buses and trams that you have to wait for and that might not even get you where you need to go? No way Jose. Drive your car? Hahahaha get outta here, don't even talk to me. But what about a BICYCLE??? Now that's the ticket.
Writer Peter Flax, the former editor-in-chief of Bicycling magazine, rode over 1,000 miles and tested 15 tools for our full-length guide to multi-tools, and he concluded the Topeak Mini 9 is the best for casual cyclists. It’s tiny, it’s light, it’s easier to get some leverage with than other tools that have different designs. It’s not meant for serious wrenching on your bike, but it’s good for on-the-fly adjustments.
Mini Pump:   This actually goes on the frame of your bike, as it’s a bit too big for most under-seat bags.   Coming soon, we’ll have a review from Bill of his very favorite one, but a good pump is a lifesaver.    Some people instead carry a CO2 inflator, which is faster and easier to use but does require disposable cartridges, and each time you have a flat, you’ll need at least 2 of those cartridges.  There are combined pump/inflator tools that we’ll also talk about soon.

The Bicycle Repair Shop is the place to be if you want to buy a new bike, need a repair or to rent a bike. These guy know everything about bikes and then some and at an amazing price. If you need your bike repaired they go above and beyond to help you get your bike repaired. If you are a tourist the shop has a great many bikes to choose from at an excellent price. I visited this shop last time I was in Seattle visiting my son and we rented the tandem bike it was a blast. My son bought a great bike and if he needs a tune up he goes to The Bicycle Repair Shop. This is the best bike shop in all of Seattle !!!!!!!


The thumb test is the fine art of pressing on the tube with your thumb to see if it’s inflated. During testing, I took a pressure reading out of curiosity, and to the touch, road tires feel fully inflated around 30 psi. How pathetically sad—30 psi!—when you’re probably trying to reach at least 60 psi on a mountain bike, 70 or more on a hybrid, and it only goes up from there.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
The Bicycle Repair Shop is the place to be if you want to buy a new bike, need a repair or to rent a bike. These guy know everything about bikes and then some and at an amazing price. If you need your bike repaired they go above and beyond to help you get your bike repaired. If you are a tourist the shop has a great many bikes to choose from at an excellent price. I visited this shop last time I was in Seattle visiting my son and we rented the tandem bike it was a blast. My son bought a great bike and if he needs a tune up he goes to The Bicycle Repair Shop. This is the best bike shop in all of Seattle !!!!!!!
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)

Since then, I’ve found a few decent alternatives to my dilemma: The Venzo Pro Mechanic Stand that runs at about $88, and the Cave Competitor Service Post for $59. While there are other alternatives out there—sometimes cheaper ones—these are the two that I think are actually worth the price. I can’t really vouch for any others out there. But there just ain’t getting around this one. You’ll need something to hold your bike while you work on it.


We focused on tools that would be useful to a commuter—someone trying to use a bike as a functional way to get around town, as opposed to riding recreationally (road biking and mountain biking). That said, it’s a wild and wooly bicycling world out there, and the streets are packed with so many different bikes, all shapes and sizes, new and old. Customizing your flat-fixing kit has advantages over buying a preassembled kit that always contains a tool (or two or three) that’s a piece of junk, or you don’t need. Or it’s missing something you do need. If you build your own kit, at least you know everything works. And you can add only what’s necessary for your specific bike without ending up with stuff you don’t need.


Riding the bus with three infants in a stroller is no easy task, especially when you realize you have a flat tire as soon as you step foot on the pavement of 2nd and University. Luckily, I found The Bicycle Repair Shop. Andy happily filled my tire with air, and when it was flat again an hour later, found a replacement tube in minutes. He changed the tire with the babies still in the stroller! This was such an amazing experience that totally made a fun day possible for us! Thank you, Andy!
Modern bottom brackets use a sealed bearing type construction that keeps water and debris locked out, so they seldom go wrong. Maintenance is impossible so they need replacing when they do wear out. Older style cup bottom brackets need to be re-greased every now and again, and occasionally will need to have their bearings replaced. There are a lot more teeth on the chainring cogs than those on the rear cassette, so need changing less regularly. Cranks usually a solid one piece construction so there is not much to go wrong.
×