Don't ever be stranded without the right tools or know-how. The Super Hero Kit for Road Biking is designed to empower all levels of cyclists to fix mechanical problems that can arise on any ride, and to get back home safely. An innovative, time-saving, and economical combination of high-quality tools and materials, and detailed instruction manual, as well as a tube, pump, and bike bag - it's an all-in-one solution - that's ready for your next ride.

First, I researched. I looked at Amazon’s top-rated products and their user reviews. Then I consulted Bicycling magazine, Gear Junkie, Bike Radar, Outside, and the occasional bit by Lennard Zinn via Velonews. I also found some worthwhile discussions at Bike Forums. Then I spoke with four experts, Ramona Marks, Scott Karoly, Cari Z, and Alison Tetrick, riders from all across the spectrum, who tour, repair, and race.


Do not take your Bike to Kyle's Bike Shop they handled my bike so poorly they can not work on Vintage Schwinn' and the attitude they had if it wasn't a high dollar bike don't expect good service. I had to find my own parts, had to take the bike back twice to get the wheel trued and they ruined my bike it is so scrapped up the Schwinn is gone on the side of the bike. If you care about your bike do not take it here.

Be organized. “I like having everything be really small and super organized. I put all of my tools in CamelBak’s Tool Roll. It’s got little compartments, and I can separate tire changing stuff in one place, stuff like extra pedal cleats or an extra derailleur hanger in another, and it all rolls up into this tidy pouch. If I do have a repair, I can pull that one thing out and lay it out on the ground and it’s easy to work.”
But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
I just got a tune up on my bike and it rides so much better now! It takes half as much effort to petal, it is like a new bike. The guys who work there are so nice and always make you feel like your time is important. They don't overcharge or sell you things you don't need. I thought for sure I needed a new chain, but as it turns out, it's fine! He gave me some extra foam for my bike helmet, free of charge! I'll definitely come back here for all my bike needs!
A wrench that fits the hub nuts:   If your bike has quick release front and rear wheels, you don’t need this, but if you have an internal hub on the back, such as the NuVinci, a wrench that fits is a great idea.  99% of the time, this is a 15mm wrench, but you should check your bike.   A 6 inch adjustable wrench can also work, but it will be heavier, and when using an adjustable wrench, you do need to take more care to not round over the nuts.   A fixed wrench is the best choice.    Some multi-tools have a 15 mm wrench built in, but again, if you have limited hand strength, something with more leverage is a great idea.
Every person who considers themselves a cycling enthusiast should know how to do at least some basic bike repairs. This is not just to satisfy an unwritten standard of being a bikehead, but because it has a lot of practical implications as well. It can make the difference between dealing with a minor issue quickly on your own or waiting a couple of days for a busy mechanic to squeeze you in. Moreover, in the long run, doing the dirty work yourself will save you a lot of money.
3D Printers Baby Bath Tub Baby Strollers Bar Stool Bean Bag Chair best actor Bike cover Blackhead Remover Boys' Boxer Underwear Car Chargers Ceiling Fans Chair Cushions cleaner Dining Chair Diving Masks Elbow Braces Electric Air Fryer Electric Stove Fizik Saddles Folding Ladders gas cooktop Handheld CB Radio inflatable boat Kindle Paperwhite Makeup Brush Makeup Chairs Men's Cycling Shoes Paper Towel Holder Ping Pong Paddles pool cue rack Preqnancy body pillow Projector Stands RC Helicopter robot rocking horse Seagrass Rug Small Indoor Dog House sound bars Table Round toddler travel bed vacuum Vanity Makeup Mirrors Walmart Folding Table Women's Condoms Wood Table Lamps
Our favorite hand pump for commuters is the Lezyne Sport Drive HP, and you can read more specifics about why in our full-length guide, written by Dave Yasuda, a writer and tester with over 30 years in the saddle. To sum it up, Lezyne makes pumps with an extendable rubber tube that connects to your tire valve, and that’s the difference between awkward and demoralizing. It’s not the only company that does so, but it is one of the few, and it does it the best. The Sport Drive HP can adapt to any tire valve, has no small fussy parts to lose, and inflates more easily to higher psi levels than anything we tested without floor leverage.
We are a full-service bike repair shop. From fixing a flat tire to packing a bike to a comprehensive tune-up, we can have you road-ready in no time. Estimates are always free: Bring your bike in and we'll recommend what repair and maintenance we think needs to be done. Many services such as flat tires and accessory installations can be done while you wait.
Before I get started, I should mention that I never leave reviews. This is probably my first one on Yelp. These guys are just so great that I felt compelled to give them a shoutout. This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. These guys will give you their best and provide some laughs as well. Couldn't recommend them more!
Packed with basic tools, this compact tin rescues puncture-interrupted bike trips. Pedaling away to a picnic spot with a pal, you hear a disconcerting "pop!". Your two-wheeler is now down one wheel, and unless you've got mad unicycle skills, you need tools. Good thing you brought this handsome, compact tin. Just break out the metal tire levers and patch kit, and you're rolling along again in no time. The six-sided, dog bone-style hex wrench adjusts the most common bike screws and bolts and screws. Made in China.
Bikes have remained popular since time in memorial. It’s fun being a rider. Their existence brings about the need to preserve their smooth riding. A bicycle like any mechanically driven tool requires regular service as they are prone to artificial failure. To ensure an outstanding service, the appropriate toolkit should be employed. It may not be easy to obtain the best toolkit, but with us, you are guaranteed quality and efficient toolkits.

2) On my second day, the pannier bag fell off and got lost after I stopped for lunch, which required locking up the bike somewhere, so I took the bag into restaurant and re-attached it using the two velcro straps on the rear rack. I've used many panniers before, thought I did it correctly. But apparently I did not. So I paid $55 (cost) to replace everything in bag and bag. In hindsight, I wished I'd put a bungee around bag straps to really secure it to bike. PROBABLY MY FAULT.


On the other hand, an on-bike repair kit will be a much smarter selection of tools that you are most likely to need. You should figure out the type of screws that are fitted on your bike and the things that are most likely to go wrong on a ride. Address only these things so as not to burden yourself too much with unnecessary stuff. Moreover, there are bike repair kits used on long rides and those used on shorter rides. The longer the ride, the more tools, and spare parts you will have to bring unless you want to have a very long hike back home.
Trek Bicycle Newington is your destination for the latest products from Trek and Bontrager, service and tune-ups for bikes of any brand, and local advice about the best riding in the area. We are proud advocates for the cycling community and we strive to give cyclists a great place to ride and learn. We host weekly road and recreational rides, women’s rides, and educational clinics aimed at getting more women on bikes. We also organize monthly mountain bike rides and sponsor several triathlon series in the area. Our store has been a community landmark since 1975, and we love seeing customers who bought their first bike with us coming back years later to get bikes for their kids. Whether you’ve been riding for years or want to try something new, we welcome you to stop in and meet our team!

Every person who considers themselves a cycling enthusiast should know how to do at least some basic bike repairs. This is not just to satisfy an unwritten standard of being a bikehead, but because it has a lot of practical implications as well. It can make the difference between dealing with a minor issue quickly on your own or waiting a couple of days for a busy mechanic to squeeze you in. Moreover, in the long run, doing the dirty work yourself will save you a lot of money.


It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
I just got a tune up on my bike and it rides so much better now! It takes half as much effort to petal, it is like a new bike. The guys who work there are so nice and always make you feel like your time is important. They don't overcharge or sell you things you don't need. I thought for sure I needed a new chain, but as it turns out, it's fine! He gave me some extra foam for my bike helmet, free of charge! I'll definitely come back here for all my bike needs!
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
We spent 26 hours on research, videography, and editing, to review the top choices for this wiki. Even recreational riders and commuters ought to conduct regular maintenance to ensure safe and proper functioning of their cycle, so you really don't have to be a professional to invest in one of these comprehensive bike repair kits. Our selections included options that cover the basics along with a few that include all the tools you're ever likely to need. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best bike repair kit on Amazon.
Professional mountain biker Rebecca Rusch has been on plenty of long rides and experienced enough mechanical failures to know what makes a fully-stocked repair kit. One of her recent journeys, a 1,200-mile journey through the jungles of Vietnam, Laos and Cambodia along the Ho Chi Minh Trail required the utmost degree of preparedness — “We brought with us a lot of extra bearings, o-rings, stuff that you would never be able to find in Laos and Cambodia. Before I go out on these big adventures, I replace every bearing in my bike, my fork got a total rebuild — everything is in pristine condition,” says Rusch.

I just got a tune up on my bike and it rides so much better now! It takes half as much effort to petal, it is like a new bike. The guys who work there are so nice and always make you feel like your time is important. They don't overcharge or sell you things you don't need. I thought for sure I needed a new chain, but as it turns out, it's fine! He gave me some extra foam for my bike helmet, free of charge! I'll definitely come back here for all my bike needs!
Good bike repair stand. I can't say "great," because it arrived with some small plastic pieces broken. These are small pieces that go between the legs and the supports for the legs to act as a sort of buffer to prevent metal to metal scraping. They are just too fragile, it seems. 3 out of 4 legs had these broken upon arrival. However, these are really only "nice" to haves, not need to haves, and they don't really detract from using the stand in any way. Once you have the stand set up, you don't worry about these at all. The main clamp holds the bike well, if you take care to balance the bike properly. The bike may tilt in the stand if you don't balance it - there is a weight limit to the clamp. I like the included tool tray, but I wish it was more adjustable in height (it is essentially fixed in one position). And the tray could be larger. Otherwise, I am quite happy with this stand. I have worked on several bikes using it, and assembled one out of the box. It makes the job of doing things like adjusting brakes and indexing derailleurs so much easier. The price of this stand is excellent considering the quality.
Next to everything else that might go wrong with a bicycle on an extended ride, a flat is a relatively minor issue that can be easily repaired trailside, if the right tools are at hand. If they aren’t, a quick fix can turn into a long walk. Well-prepared riders will perform a tune-up regularly and clean their bikes after every ride. For the less-diligent, a well-stocked repair kit will suffice.

Mini Pump:   This actually goes on the frame of your bike, as it’s a bit too big for most under-seat bags.   Coming soon, we’ll have a review from Bill of his very favorite one, but a good pump is a lifesaver.    Some people instead carry a CO2 inflator, which is faster and easier to use but does require disposable cartridges, and each time you have a flat, you’ll need at least 2 of those cartridges.  There are combined pump/inflator tools that we’ll also talk about soon.

We're Arizona's top rated and 5 times running "America's Best" Rated Bike Shop by the NBDA.  From mountain bikes, kids, comfort, fitness and road bikes we sell and service them all! Are E-bikes your thing? Our Gilbert location Is our hub for electric bike sales and service. Swing by and see us... Family owned and operated by Brandee and Al since 2001.
I bicycle to and from work to save gas. I don't have a fancy bike, it's just a Schwinn mountain bike that's comfortable and can carry me plus gear but I want to be able to do my own work on it. I needed a book that was simple enough for someone new to bicycle repair and maintenance but could take me through all the upkeep my workhorse needs, and this book does just that. It's well-written and easy to follow.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
×