Writer Peter Flax, the former editor-in-chief of Bicycling magazine, rode over 1,000 miles and tested 15 tools for our full-length guide to multi-tools, and he concluded the Topeak Mini 9 is the best for casual cyclists. It’s tiny, it’s light, it’s easier to get some leverage with than other tools that have different designs. It’s not meant for serious wrenching on your bike, but it’s good for on-the-fly adjustments.
Based on what we found, we chose the most relevant items and used them all. To test patches, I repaired holes using four different types of patches, from Novara (REI’s now-discontinued house brand), Park Tool, and Rema. Patching a tube isn’t hard but there are a few tricks, and the key was attention to detail and patience. I was extremely diligent in following proper patch procedure, which includes a thorough sanding of the entire area to be patched (for max stickiness) and properly letting the vulcanizer dry on both surfaces before applying. For the peel-and-stick patches, I went so far as to prep the area with canned air to ensure as tight a seal as we could possibly muster.
But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
Good bike repair stand. I can't say "great," because it arrived with some small plastic pieces broken. These are small pieces that go between the legs and the supports for the legs to act as a sort of buffer to prevent metal to metal scraping. They are just too fragile, it seems. 3 out of 4 legs had these broken upon arrival. However, these are really only "nice" to haves, not need to haves, and they don't really detract from using the stand in any way. Once you have the stand set up, you don't worry about these at all. The main clamp holds the bike well, if you take care to balance the bike properly. The bike may tilt in the stand if you don't balance it - there is a weight limit to the clamp. I like the included tool tray, but I wish it was more adjustable in height (it is essentially fixed in one position). And the tray could be larger. Otherwise, I am quite happy with this stand. I have worked on several bikes using it, and assembled one out of the box. It makes the job of doing things like adjusting brakes and indexing derailleurs so much easier. The price of this stand is excellent considering the quality.
Bike Radar gives the Pedro’s levers 4.55 out of five stars and claims they’re the “best out there.” (Can we pause to admire the extra five hundredths of a star the site chose to award it? Very specific.) Aaron Gulley, writing for Outside, states, “I can’t count the number of times I’ve snapped cheap plastic sticks, shredded my hand in the process, stomped around cursing in pain for 10 minutes, and then, insult to injury, been tool-less and unable to get my tire off anyway. That will never happen with Pedro’s.”
These are some great ideas, especially the simple ones like bringing a garbage bag. That’s something so easy and cheap that it’s easy to forget entirely, but as you say, it can make a huge difference in the right circumstances. It’s also good that you discuss some minor bike repairs. That’s another thing that can salvage or destroy your ride. You want to be as prepared as possible for the best possible experience.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Before I get started, I should mention that I never leave reviews. This is probably my first one on Yelp. These guys are just so great that I felt compelled to give them a shoutout. This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. These guys will give you their best and provide some laughs as well. Couldn't recommend them more!
Bike Radar gives the Pedro’s levers 4.55 out of five stars and claims they’re the “best out there.” (Can we pause to admire the extra five hundredths of a star the site chose to award it? Very specific.) Aaron Gulley, writing for Outside, states, “I can’t count the number of times I’ve snapped cheap plastic sticks, shredded my hand in the process, stomped around cursing in pain for 10 minutes, and then, insult to injury, been tool-less and unable to get my tire off anyway. That will never happen with Pedro’s.”
Don't ever be stranded without the right tools or know-how. The Super Hero Kit for Road Biking is designed to empower all levels of cyclists to fix mechanical problems that can arise on any ride, and to get back home safely. An innovative, time-saving, and economical combination of high-quality tools and materials, and detailed instruction manual, as well as a tube, pump, and bike bag - it's an all-in-one solution - that's ready for your next ride.
Whether you ride a single, 7, or 10 speed bike or anything in between, you will need a slightly different chain. The major difference is that they come in varying widths to accomodate the different spaces between the gears, but quality of construction is also a factor in choosing a chain. Inspecing the chain should be a part of your regular cycle maintenance procedure- It’s important to keep a chain well lubricated, but oil will also attract dirt and so different oils for specific riding conditions are available. Remember to clean your chain regularly to get the longest life out of it and the gears.
×