It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
More than any other tool in the kit, a reliable lever makes changing a tire easier, especially if you have road bike tires, which are difficult to remove. However, throughout testing, levers seemed to be the one item more prone to failure and poor design than anything else. For example, I found a random orange lever floating around my basement and I threw it in the test pool for fun—it seemed solid enough … until I began prying at the rim of a tire. It bent directly in half, slowly and smoothly, like taffy, and then was boomerang shaped forevermore.
On the other hand, an on-bike repair kit will be a much smarter selection of tools that you are most likely to need. You should figure out the type of screws that are fitted on your bike and the things that are most likely to go wrong on a ride. Address only these things so as not to burden yourself too much with unnecessary stuff. Moreover, there are bike repair kits used on long rides and those used on shorter rides. The longer the ride, the more tools, and spare parts you will have to bring unless you want to have a very long hike back home.
The fabric attachment system is low-tech, but that seems to be helpful, as it can adapt to seat rails of different widths. One fancier option you might see on more expensive seat bags is a quick-release mount that you install under your saddle. But those have a fixed width, and therefore can fit under seats with only those exact specs. Brooks saddles, for example, are too wide for these mounts.
Good bike repair stand. I can't say "great," because it arrived with some small plastic pieces broken. These are small pieces that go between the legs and the supports for the legs to act as a sort of buffer to prevent metal to metal scraping. They are just too fragile, it seems. 3 out of 4 legs had these broken upon arrival. However, these are really only "nice" to haves, not need to haves, and they don't really detract from using the stand in any way. Once you have the stand set up, you don't worry about these at all. The main clamp holds the bike well, if you take care to balance the bike properly. The bike may tilt in the stand if you don't balance it - there is a weight limit to the clamp. I like the included tool tray, but I wish it was more adjustable in height (it is essentially fixed in one position). And the tray could be larger. Otherwise, I am quite happy with this stand. I have worked on several bikes using it, and assembled one out of the box. It makes the job of doing things like adjusting brakes and indexing derailleurs so much easier. The price of this stand is excellent considering the quality.
Professional mountain biker Rebecca Rusch has been on plenty of long rides and experienced enough mechanical failures to know what makes a fully-stocked repair kit. One of her recent journeys, a 1,200-mile journey through the jungles of Vietnam, Laos and Cambodia along the Ho Chi Minh Trail required the utmost degree of preparedness — “We brought with us a lot of extra bearings, o-rings, stuff that you would never be able to find in Laos and Cambodia. Before I go out on these big adventures, I replace every bearing in my bike, my fork got a total rebuild — everything is in pristine condition,” says Rusch.
Yes, bicycle shops generally provide repair services. A typical list of offered services includes regular service/adjustment (including safety check; and  brake, drivetrain, and tire inspection); premium, and annual service, which is a more extensive tune-up. More specific repairs include drivetrain tune-up, brake system tune-up, flat tire fixes, brake repairs, cleaning and touching up the bike frame.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Brakes come in a variety of designs depending on the age and style of your bike. Rim brakes offer more modulation but have less stopping power, so are more suited to riding on the roads. Disc brakes can provide huge amounts of stopping power so are best suited to off road riding, although ‘V’ rim brakes are also well suited to mountain biking. All brakes use a friction system to stop the movement of the wheel, so regular checks of the contact pads should form part of your regular cycle maintenance.
×