It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.

Create emergency patches on tires or tubes with this Bike Tire Repair Kit. Each pack comes with everything you need to fix a flat, including a spokes wrench. When you find a puncture or nail hole in your riding essential, grab an application from this bicycle repair kit to hold in enough air so you can continue on your way until a replacement tire can be located. It includes adhesives and patches of different sizes for your convenience. Made of steel, the bicycle tire repair kit is durable and long-lasting. Keep the set with you at all times while riding your bicycle so that you have it in the event of an emergency. The size of the kit makes it easy to carry in a backpack or zippered cargo bag. Cover different sizes and types of holes and tears that make riding difficult with this Bike Tire Repair Kit.


If you are planning on going on a multi-day ride or just riding a long distance in a day, you should have something for first aid, just in case. Unfortunately, almost everyone who cycles frequently will go down at least once in their life. This kit can be really small and compact and can include bandages, some gauze, and a small bottle of a disinfectant.

Good bike repair stand. I can't say "great," because it arrived with some small plastic pieces broken. These are small pieces that go between the legs and the supports for the legs to act as a sort of buffer to prevent metal to metal scraping. They are just too fragile, it seems. 3 out of 4 legs had these broken upon arrival. However, these are really only "nice" to haves, not need to haves, and they don't really detract from using the stand in any way. Once you have the stand set up, you don't worry about these at all. The main clamp holds the bike well, if you take care to balance the bike properly. The bike may tilt in the stand if you don't balance it - there is a weight limit to the clamp. I like the included tool tray, but I wish it was more adjustable in height (it is essentially fixed in one position). And the tray could be larger. Otherwise, I am quite happy with this stand. I have worked on several bikes using it, and assembled one out of the box. It makes the job of doing things like adjusting brakes and indexing derailleurs so much easier. The price of this stand is excellent considering the quality.

If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
A good patch will stick to your tube enough to keep air from leaking out. A great patch will act like a second skin and actually strengthen the tube where it’s applied, flexing and stretching with the tire. After 36 hours of testing, our official endorsement goes to the Rema TT 02 Touring Repair Kit. Its patches do everything other patches do, just better. The edge of the patch is also ruffled, which provides more edge surface area to bond—that’s a good thing.

A wrench that fits the hub nuts:   If your bike has quick release front and rear wheels, you don’t need this, but if you have an internal hub on the back, such as the NuVinci, a wrench that fits is a great idea.  99% of the time, this is a 15mm wrench, but you should check your bike.   A 6 inch adjustable wrench can also work, but it will be heavier, and when using an adjustable wrench, you do need to take more care to not round over the nuts.   A fixed wrench is the best choice.    Some multi-tools have a 15 mm wrench built in, but again, if you have limited hand strength, something with more leverage is a great idea.
Inside Student Union across from College Optical, the UCF Bike Repair Service is provided for students with bike problems. Students may come, free of charge, and have their bikes repaired with quality service by our Bike Repair Team. Service include: Inflate tires, change tubes, brake adjustments, tighten crankset, loose handlebars, adjust gears, and brake cable installation. Bikes can also be reserved here as part of the Bike Share program.
×