If you own a bike, you need a flat-fixing kit. It’s really that simple. Sure, maybe you’ll get lucky and get a flat close to a shop, or the buses will be running on time for once, but even with all that going for you, getting stranded across town will cost you time, money, and precious sanity. You can put together a great kit in less time than it takes to read this guide.
We are a full-service bike repair shop. From fixing a flat tire to packing a bike to a comprehensive tune-up, we can have you road-ready in no time. Estimates are always free: Bring your bike in and we'll recommend what repair and maintenance we think needs to be done. Many services such as flat tires and accessory installations can be done while you wait.

Create emergency patches on tires or tubes with this Bike Tire Repair Kit. Each pack comes with everything you need to fix a flat, including a spokes wrench. When you find a puncture or nail hole in your riding essential, grab an application from this bicycle repair kit to hold in enough air so you can continue on your way until a replacement tire can be located. It includes adhesives and patches of different sizes for your convenience. Made of steel, the bicycle tire repair kit is durable and long-lasting. Keep the set with you at all times while riding your bicycle so that you have it in the event of an emergency. The size of the kit makes it easy to carry in a backpack or zippered cargo bag. Cover different sizes and types of holes and tears that make riding difficult with this Bike Tire Repair Kit.


To pick the right size bicycle, you want to measure your height, and specifically your inseam (inside leg), in proportion to the size of the bike frame. The inseam measurement determines the seat height, or the “stack.” Next, you must calculate the “reach,” which is the horizontal distance between the bottom of the frame and the head of the bike -- or, in layman’s terms, the distance between seat and handlebars.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.

First, I researched. I looked at Amazon’s top-rated products and their user reviews. Then I consulted Bicycling magazine, Gear Junkie, Bike Radar, Outside, and the occasional bit by Lennard Zinn via Velonews. I also found some worthwhile discussions at Bike Forums. Then I spoke with four experts, Ramona Marks, Scott Karoly, Cari Z, and Alison Tetrick, riders from all across the spectrum, who tour, repair, and race.
We rented a tandem bike from here for an hour, and they were super chill! We dropped by on a Sunday and decided to go eat first; Andy, one of the owners, was awesome about holding the bike for us while we went to eat before renting. We enjoyed our ride for just over an hr, but Andy was also super relaxed about our return time and only charged us for an hour. We had a fantastic time and would definitely recommend renting bikes from here!
I own the Lezyne CNC Chain Rod, which I’m a big fan of (yes, I know I’m partial to Lezyne here–they’re a local-to-me, San Luis Obispo company and they sponsored my collegiate team, so I got tons of gear) and it costs right around $30. But the truth is that even the cheapest of chain whips will likely do the job. In fact, I’ve found a dude who knows his stuff and shows you how to make this tool all by yourself. I would even go so far as to say that you probably have enough materials laying about your garage (if not, try your parents’ garage ? ) to put this together without spending anything. Check out the video below:
We offer several bicycle repair packages, or individual services in the case that you don’t need a full “tune-up”. Whether it’s a small brake adjustment or a complete bike overhaul, we’re happy to help. Our highly experienced staff is here to answer any questions you may have and will help get you and your bike back on the road as quickly as possible.
×