Be organized. “I like having everything be really small and super organized. I put all of my tools in CamelBak’s Tool Roll. It’s got little compartments, and I can separate tire changing stuff in one place, stuff like extra pedal cleats or an extra derailleur hanger in another, and it all rolls up into this tidy pouch. If I do have a repair, I can pull that one thing out and lay it out on the ground and it’s easy to work.”
First, carbon. You already know you don’t need it for your casual weekend pursuits, because you’re not counting ounces the way a professional road racer would. But to quote an article from Velonews, “Remember that professional athletes operate in an entirely different environment than the rest of us. They are all very close to each other in terms of fitness, and they are also all very close to being the absolute best a human being can be. In short, you’re much better off upgrading your legs and dropping body fat through proper training and diet.”
The Administration & Event Services office is critical to every thing that happens at the heart of the UCF campus. They are your first stop when planning anything that happens at the Student Union. So whether it's providing logistics for your upcoming event, making room reservations or offering you guidance on proper procedure, the Student Union staff is here to help.
Where to begin?! Long story made somewhat short. I bookmarked this place because I saw their dog Kaya and was sold. Lol. But they had 5 stars too so that helped. Amazing people. Very down-to-earth. Took the bikes down the path to Discovery Park. If you're in-shape and do mild cardio, then it should be an ok ride. I don't do cardio and I found myself trying to sell my soul like 15 times just to get to the top of some hills. Lol. Made it to the Ballard locks and actually got to see a boat pass through! This is the off-season so not much boat traffic. Steve, an engineer we met there, said peak time will start in May. Ate lunch at Ann's in Ballard. Delish shrimp sate! I busted my tire in a pothole and had to make a trip to REI. Which wasn't awful because we wanted to go there anyway. The city was tough to ride in at 5:00pm and we rode the sidewalk most of the way back due to the congestion. Some pedestrians are obvious to you and I almost ran over a few people.. By choice. Lol. Made it back right before they closed at 6:00pm. Easy peasy! Notes: Take some water. Take some pictures. The ride is beautiful so don't rush through. Get there before noon to give yourself some time to cruise.
We focused on tools that would be useful to a commuter—someone trying to use a bike as a functional way to get around town, as opposed to riding recreationally (road biking and mountain biking). That said, it’s a wild and wooly bicycling world out there, and the streets are packed with so many different bikes, all shapes and sizes, new and old. Customizing your flat-fixing kit has advantages over buying a preassembled kit that always contains a tool (or two or three) that’s a piece of junk, or you don’t need. Or it’s missing something you do need. If you build your own kit, at least you know everything works. And you can add only what’s necessary for your specific bike without ending up with stuff you don’t need.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Every expert I spoke to recommended Pedro’s Tire Levers by name. They have a wide body—a different shape than other models we tested—and that prevents breakage, but more important, the broad, flat surface area of the tip helps it stay locked under your tire. When a lever slips from under the bead of the tire, you can end up repeatedly scraping your knuckles on the spokes of the wheel, which is so annoying. Pedro’s levers are small enough to fit into a saddlebag, are sold widely in bike shops, and even come with a lifetime guarantee. If one breaks, Pedro’s will replace it.
Before I get started, I should mention that I never leave reviews. This is probably my first one on Yelp. These guys are just so great that I felt compelled to give them a shoutout. This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. These guys will give you their best and provide some laughs as well. Couldn't recommend them more!
But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
The Knights Helping Knights Pantry is a student driven program at the University of Central Florida with the goal of assisting students through financially tough times. Donations that are either brought to the Pantry or are left in one of our 15 drop boxes on campus are provided by faculty, staff and students. Student organizations, departments and individuals on campus also organize food drives that benefit the Pantry.