A multitool is a highly versatile piece of repair equipment that can address most of your maintenance needs. Ideally, you should use it before a ride to tighten and adjust everything properly, but sometimes it’s necessary on a ride as well. If you encounter a loose screw, realize your saddle height is not right, or that your brakes need tightening, you will be happy to have it.
Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.
That’s a reality of all hand pumps—it’s really hard to get a tire up to pressure with these things. So another reason Lezyne pumps are so good is because you can actually keep pumping longer than any other brand we tested. With excruciating effort, we could get the Sport Drive HP to pump tires to 90 or 100 psi. It still wasn’t easy, but it wasn’t impossible the way it was with some other models.

Based on what we found, we chose the most relevant items and used them all. To test patches, I repaired holes using four different types of patches, from Novara (REI’s now-discontinued house brand), Park Tool, and Rema. Patching a tube isn’t hard but there are a few tricks, and the key was attention to detail and patience. I was extremely diligent in following proper patch procedure, which includes a thorough sanding of the entire area to be patched (for max stickiness) and properly letting the vulcanizer dry on both surfaces before applying. For the peel-and-stick patches, I went so far as to prep the area with canned air to ensure as tight a seal as we could possibly muster.
We like, and recommend, the Crankbrothers Speedier Lever. If you have to pick only one, go with the Pedro’s, but if you want a backup or have some hard tires to unseat, Crankbrothers is a great choice. It’s only one lever (as opposed to a set of two, like the Pedro’s) and it’s longer, so we didn’t pick it over the Pedro’s for portability reasons. But it’s an excellent tool. It has a wide handle you can grip with your whole hand. Like the Pedro’s, the tip is the right size and shape to prevent slipping and stay in place, and the shape of the handle happens to protect your knuckles if you do slip. Even in situations where I didn’t need it, I liked having it because it made me feel like a pro.
A wrench that fits the hub nuts:   If your bike has quick release front and rear wheels, you don’t need this, but if you have an internal hub on the back, such as the NuVinci, a wrench that fits is a great idea.  99% of the time, this is a 15mm wrench, but you should check your bike.   A 6 inch adjustable wrench can also work, but it will be heavier, and when using an adjustable wrench, you do need to take more care to not round over the nuts.   A fixed wrench is the best choice.    Some multi-tools have a 15 mm wrench built in, but again, if you have limited hand strength, something with more leverage is a great idea.
Next to everything else that might go wrong with a bicycle on an extended ride, a flat is a relatively minor issue that can be easily repaired trailside, if the right tools are at hand. If they aren’t, a quick fix can turn into a long walk. Well-prepared riders will perform a tune-up regularly and clean their bikes after every ride. For the less-diligent, a well-stocked repair kit will suffice.
These guys are awesome.  After work, I got to my bike to discover my back tire was completely flat.  It had a slow leak, so I was able to pump it up enough to make it to their shop.  I got there 10 minutes before closing and they were able to fit me in.  They replaced my tube and picked all of the glass shards out of my tire.  Awesome customer service and they saved me from having to do this myself in the dark and the cold.
Modern bottom brackets use a sealed bearing type construction that keeps water and debris locked out, so they seldom go wrong. Maintenance is impossible so they need replacing when they do wear out. Older style cup bottom brackets need to be re-greased every now and again, and occasionally will need to have their bearings replaced. There are a lot more teeth on the chainring cogs than those on the rear cassette, so need changing less regularly. Cranks usually a solid one piece construction so there is not much to go wrong.
×