We spoke to a broad spectrum of cyclists—from a pro racer to a bike messenger turned mechanic to a touring cyclist who has logged thousands of miles throughout Europe—to find out what items they find indispensable. We sorted through 40 tire levers, almost 30 different kinds of patches, 120 different hand pumps, and 57 seat bags before we narrowed our choices for testing. And then we changed and patched tires more than 50 times, using four different bikes, five different wheels, six different tires, and almost 10 different sizes of tubes. After 96 hours of combined testing, we agree these essentials are some of the best you can buy.
The Pedro’s lever slipped only once throughout testing, though that may have been my fault because I was spaced out after changing 16 different tires. So they’re not foolproof, but they are far and away more reliable than the next closest competitor, from Park Tool, because the small, rounded tip on that one is hard to keep seated under the tire. Not impossible, but I wouldn’t choose it over Pedro’s.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
​High quality bike repair stand features with 360° swivel head and adjustable height. It is convenient to use our bicycle repair stand no matter you are sitting or standing. Covered by plastic, the clamp keeps your bike in place and protects the paint of your bike nicely. Made from sturdy metal, this bike work stand can holds up to 30kg/66 lb. It is a perfect choice for bike enthusiasts, bike clubs, bike shops and bike repair shops.

If you own a bike, you need a flat-fixing kit. It’s really that simple. Sure, maybe you’ll get lucky and get a flat close to a shop, or the buses will be running on time for once, but even with all that going for you, getting stranded across town will cost you time, money, and precious sanity. You can put together a great kit in less time than it takes to read this guide.
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
The retractable tube is stored inside the body of the pump when not in use, and it can attach to either a Schrader or a Presta valve, the two types of valves you’ll see. Some pumps can accommodate only one type, making them less universal. Toggling between the two is simple, which can’t be said of other models with itty parts that require nerves of steel to handle on a good day, let alone while wearing gloves, crouching in the wind, oblivious to the sewer grate a few feet away.
First, carbon. You already know you don’t need it for your casual weekend pursuits, because you’re not counting ounces the way a professional road racer would. But to quote an article from Velonews, “Remember that professional athletes operate in an entirely different environment than the rest of us. They are all very close to each other in terms of fitness, and they are also all very close to being the absolute best a human being can be. In short, you’re much better off upgrading your legs and dropping body fat through proper training and diet.”
To pick the right size bicycle, you want to measure your height, and specifically your inseam (inside leg), in proportion to the size of the bike frame. The inseam measurement determines the seat height, or the “stack.” Next, you must calculate the “reach,” which is the horizontal distance between the bottom of the frame and the head of the bike -- or, in layman’s terms, the distance between seat and handlebars.
The thumb test is the fine art of pressing on the tube with your thumb to see if it’s inflated. During testing, I took a pressure reading out of curiosity, and to the touch, road tires feel fully inflated around 30 psi. How pathetically sad—30 psi!—when you’re probably trying to reach at least 60 psi on a mountain bike, 70 or more on a hybrid, and it only goes up from there.
Brakes come in a variety of designs depending on the age and style of your bike. Rim brakes offer more modulation but have less stopping power, so are more suited to riding on the roads. Disc brakes can provide huge amounts of stopping power so are best suited to off road riding, although ‘V’ rim brakes are also well suited to mountain biking. All brakes use a friction system to stop the movement of the wheel, so regular checks of the contact pads should form part of your regular cycle maintenance.
×