We like, and recommend, the Crankbrothers Speedier Lever. If you have to pick only one, go with the Pedro’s, but if you want a backup or have some hard tires to unseat, Crankbrothers is a great choice. It’s only one lever (as opposed to a set of two, like the Pedro’s) and it’s longer, so we didn’t pick it over the Pedro’s for portability reasons. But it’s an excellent tool. It has a wide handle you can grip with your whole hand. Like the Pedro’s, the tip is the right size and shape to prevent slipping and stay in place, and the shape of the handle happens to protect your knuckles if you do slip. Even in situations where I didn’t need it, I liked having it because it made me feel like a pro.
Patch kit:   Patch kits are easy to use, light and compact, and if you get more than one flat on a ride (it happens more than you’d expect), it can save you when you’ve already used your spare tube.   Plus, on a rear wheel, patching a tube can be faster than replacing it, as you can often do this without removing the wheel at all.  Another upcoming post is going to show you how to patch a tube.
As you mentioned, it is surprising how often you can get multiple flat tires on while riding, particularly on longer sprints. The tip about bringing a patch kit in your bike repair kit can be incredibly helpful if you’ve already had one flat tire. I agree that all you listed seems like an awful lot to carry, but it’s always better to be safe than sorry, isn’t it?
Many bikes, including older models and track bikes, have bolts attaching the wheels to the frame instead of quick-release levers. If your wheels are bolted on, in most cases you’ll need a 15 mm wrench to remove it. We didn’t test wrenches, because there aren’t that many tiny 15 mm wrenches, but the GearWrench 15mm 12-Point Stubby Combination Wrench is perfect for stuffing into a flat kit and Amazon reviewers seem to think the same. Our experts also recommended the Surly Jethro Tule, but it’s expensive and harder to find.
To pick the right size bicycle, you want to measure your height, and specifically your inseam (inside leg), in proportion to the size of the bike frame. The inseam measurement determines the seat height, or the “stack.” Next, you must calculate the “reach,” which is the horizontal distance between the bottom of the frame and the head of the bike -- or, in layman’s terms, the distance between seat and handlebars.
As you mentioned, it is surprising how often you can get multiple flat tires on while riding, particularly on longer sprints. The tip about bringing a patch kit in your bike repair kit can be incredibly helpful if you’ve already had one flat tire. I agree that all you listed seems like an awful lot to carry, but it’s always better to be safe than sorry, isn’t it?
Man, if you're starting out and you know you'll need several components for a bag... just get this. It will save you so much time picking everything out that even if you balk at the price (amazing value, by the way) I bet that if you did the math using your hourly wage and the time spent picking everything out and making sure it fits... you'd save a lot of money and a lot of irritation if you just got this. Just get this.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
Bike Radar gives the Pedro’s levers 4.55 out of five stars and claims they’re the “best out there.” (Can we pause to admire the extra five hundredths of a star the site chose to award it? Very specific.) Aaron Gulley, writing for Outside, states, “I can’t count the number of times I’ve snapped cheap plastic sticks, shredded my hand in the process, stomped around cursing in pain for 10 minutes, and then, insult to injury, been tool-less and unable to get my tire off anyway. That will never happen with Pedro’s.”

Modern bottom brackets use a sealed bearing type construction that keeps water and debris locked out, so they seldom go wrong. Maintenance is impossible so they need replacing when they do wear out. Older style cup bottom brackets need to be re-greased every now and again, and occasionally will need to have their bearings replaced. There are a lot more teeth on the chainring cogs than those on the rear cassette, so need changing less regularly. Cranks usually a solid one piece construction so there is not much to go wrong.
×