If you have just a short time in Seattle there is only one way to see the city. Walk at 2.5 miles an hour? I don't think so. Take buses and trams that you have to wait for and that might not even get you where you need to go? No way Jose. Drive your car? Hahahaha get outta here, don't even talk to me. But what about a BICYCLE??? Now that's the ticket.
But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
Based on what we found, we chose the most relevant items and used them all. To test patches, I repaired holes using four different types of patches, from Novara (REI’s now-discontinued house brand), Park Tool, and Rema. Patching a tube isn’t hard but there are a few tricks, and the key was attention to detail and patience. I was extremely diligent in following proper patch procedure, which includes a thorough sanding of the entire area to be patched (for max stickiness) and properly letting the vulcanizer dry on both surfaces before applying. For the peel-and-stick patches, I went so far as to prep the area with canned air to ensure as tight a seal as we could possibly muster.
Dennis Bailey has been actively involved in bike repair and maintenance for almost two decades. He has worked on bikes on bike tours in the United States, Europe, and Latin America. Keith Gates has been repairing bikes for more than 30 years and provides personalized service as the owner of A-1 Cycling, with locations in Manassas and Herndon, Virginia.
Don’t rely on others. “People need to recognize that now there are different cassette sizes, so there are different chains depending on what gear you have. A lot of people are like, ‘Oh my friend is always prepared they always have the stuff, I’m not going to bring anything.’ All of the stuff now is very bike-specific, and you have to have your own package of stuff.”

Now you might be wondering: “I’m carrying a tube; why carry patches at all?” As insurance for the unforeseeable. Wirecutter senior editor Christine Ryan admits she didn’t use to pack them, but said, “I’ve regretted that decision when I’ve had a flat on a ride, used my spare tube, and then, half an hour later, had a second flat. Also, lots of people aren’t very good at figuring out—or don’t take the time to figure out—what caused their flat and remove the cause: thorn, eensy bit of glass, whatever. Then they promptly have a second flat, and everyone else laughs at them.”
If you have just a short time in Seattle there is only one way to see the city. Walk at 2.5 miles an hour? I don't think so. Take buses and trams that you have to wait for and that might not even get you where you need to go? No way Jose. Drive your car? Hahahaha get outta here, don't even talk to me. But what about a BICYCLE??? Now that's the ticket.
Professional mountain biker Rebecca Rusch has been on plenty of long rides and experienced enough mechanical failures to know what makes a fully-stocked repair kit. One of her recent journeys, a 1,200-mile journey through the jungles of Vietnam, Laos and Cambodia along the Ho Chi Minh Trail required the utmost degree of preparedness — “We brought with us a lot of extra bearings, o-rings, stuff that you would never be able to find in Laos and Cambodia. Before I go out on these big adventures, I replace every bearing in my bike, my fork got a total rebuild — everything is in pristine condition,” says Rusch.

On the other hand, an on-bike repair kit will be a much smarter selection of tools that you are most likely to need. You should figure out the type of screws that are fitted on your bike and the things that are most likely to go wrong on a ride. Address only these things so as not to burden yourself too much with unnecessary stuff. Moreover, there are bike repair kits used on long rides and those used on shorter rides. The longer the ride, the more tools, and spare parts you will have to bring unless you want to have a very long hike back home.
If you are planning on going on a multi-day ride or just riding a long distance in a day, you should have something for first aid, just in case. Unfortunately, almost everyone who cycles frequently will go down at least once in their life. This kit can be really small and compact and can include bandages, some gauze, and a small bottle of a disinfectant.
These guys are awesome.  After work, I got to my bike to discover my back tire was completely flat.  It had a slow leak, so I was able to pump it up enough to make it to their shop.  I got there 10 minutes before closing and they were able to fit me in.  They replaced my tube and picked all of the glass shards out of my tire.  Awesome customer service and they saved me from having to do this myself in the dark and the cold.
All multi-tools are not created equal, but most with a plethora of features will get plenty of the jobs done. I personally like, and use often, the Lezyne RAP-21 LED tool, which will run you around $30. I like it because not only is it a high quality construction, but it has just about everything you’ll need, plus a sweet mini light. This will give you a chain breaker, spoke wrench, disc brake wedge, and all the most often used Allen keys and drivers. We’re talking a decent number of tools for 1/4 of what they would cost buying them separately.
​High quality bike repair stand features with 360° swivel head and adjustable height. It is convenient to use our bicycle repair stand no matter you are sitting or standing. Covered by plastic, the clamp keeps your bike in place and protects the paint of your bike nicely. Made from sturdy metal, this bike work stand can holds up to 30kg/66 lb. It is a perfect choice for bike enthusiasts, bike clubs, bike shops and bike repair shops.
I own the Lezyne CNC Chain Rod, which I’m a big fan of (yes, I know I’m partial to Lezyne here–they’re a local-to-me, San Luis Obispo company and they sponsored my collegiate team, so I got tons of gear) and it costs right around $30. But the truth is that even the cheapest of chain whips will likely do the job. In fact, I’ve found a dude who knows his stuff and shows you how to make this tool all by yourself. I would even go so far as to say that you probably have enough materials laying about your garage (if not, try your parents’ garage ? ) to put this together without spending anything. Check out the video below:
Dennis Bailey has been actively involved in bike repair and maintenance for almost two decades. He has worked on bikes on bike tours in the United States, Europe, and Latin America. Keith Gates has been repairing bikes for more than 30 years and provides personalized service as the owner of A-1 Cycling, with locations in Manassas and Herndon, Virginia.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
We spoke to a broad spectrum of cyclists—from a pro racer to a bike messenger turned mechanic to a touring cyclist who has logged thousands of miles throughout Europe—to find out what items they find indispensable. We sorted through 40 tire levers, almost 30 different kinds of patches, 120 different hand pumps, and 57 seat bags before we narrowed our choices for testing. And then we changed and patched tires more than 50 times, using four different bikes, five different wheels, six different tires, and almost 10 different sizes of tubes. After 96 hours of combined testing, we agree these essentials are some of the best you can buy.
It includes nine tools: seven hex bolts, one torx bolt (the star-shaped one), and a Phillips screwdriver (also the star-shaped one). Like Peter says in our guide, if you have a newer mountain bike or road bike it pays to take a quick look at what types of tools you need, as torx bolts are becoming more common. And a quick glance at the bottom of your shoes or derailleur bolts will confirm if a Phillips head is the right choice.
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.

It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.


A pair of disposable latex gloves:  Not absolutely necessary, but good for keeping grease and grime off your hands during a repair.  Also, nice to have in an emergency when it starts raining and the temperature drops 20 degrees and you don’t have a pair of regular gloves.   Just keeping your hands dry and the wind from directly blowing on them makes a huge difference in comfort.
This is a very basic book and unnecessarily repetitive in sections. It does introduce the reader to the basic nomenclature of bicycles and this is helpful when conversing with others. Unfortunately the repetitive sections were not replaced with chapters on 3 Speed in hub gear drives, or coaster breaks, or a chapter on Adult Tricycles and Tandems and E-Bikes.
Some years ago, I used to live on my bike. Riding around daily through any weather condition was bound to quickly wear down on the bike over time. I like some of the stuff that you have in your toolkit. I would say zip ties are actually really convenient, because when something came loose you could go ahead and use those to fasten them down to keep on moving ahead until you had enough time to fix it or get it checked at a bike repair shop.
The SGA Bike Share is open to all students with a valid UCF Card. There is no rental fee to rent a bicycle, lock, helmet, and light for one work day. Participants may rent and return our bikes from the following four locations: the Student Union, Recreation and Wellness Center, RWC @ Knights Plaza and Lake Claire Apartments. Use of our equipment is strictly on a first-come-first-served basis.
×