Some years ago, I used to live on my bike. Riding around daily through any weather condition was bound to quickly wear down on the bike over time. I like some of the stuff that you have in your toolkit. I would say zip ties are actually really convenient, because when something came loose you could go ahead and use those to fasten them down to keep on moving ahead until you had enough time to fix it or get it checked at a bike repair shop.

This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement.
A multitool is a highly versatile piece of repair equipment that can address most of your maintenance needs. Ideally, you should use it before a ride to tighten and adjust everything properly, but sometimes it’s necessary on a ride as well. If you encounter a loose screw, realize your saddle height is not right, or that your brakes need tightening, you will be happy to have it.
First, carbon. You already know you don’t need it for your casual weekend pursuits, because you’re not counting ounces the way a professional road racer would. But to quote an article from Velonews, “Remember that professional athletes operate in an entirely different environment than the rest of us. They are all very close to each other in terms of fitness, and they are also all very close to being the absolute best a human being can be. In short, you’re much better off upgrading your legs and dropping body fat through proper training and diet.”
I brought my bike into Kyle's shop to fix the noise in my rear wheel. The mechanic suggested that I need to overhauled the rear hub for $30. The next day the noise came back even worst. I brought it back to the shop and they said it was the freewheel driver not the hub that needed to be work on and it would cost me extra $30 to overhauled it again plus the part to fix it. At this point I walked out of the shop and took my bike to David's world. The mechanic at David's world took a quick look at the rear hub and indicated that the axle was put back too tight when Kyle's mechanics were working on it and further identify the issue. I ended up paying David's world the $30 plus part to fix my bike, but the major different is that David's World has 30 Days services warranty claim. If you have any issue with your bike within the 30 days the service was performed you can bring it back and they will fix it no question ask.
We spent 26 hours on research, videography, and editing, to review the top choices for this wiki. Even recreational riders and commuters ought to conduct regular maintenance to ensure safe and proper functioning of their cycle, so you really don't have to be a professional to invest in one of these comprehensive bike repair kits. Our selections included options that cover the basics along with a few that include all the tools you're ever likely to need. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best bike repair kit on Amazon.

Since then, I’ve found a few decent alternatives to my dilemma: The Venzo Pro Mechanic Stand that runs at about $88, and the Cave Competitor Service Post for $59. While there are other alternatives out there—sometimes cheaper ones—these are the two that I think are actually worth the price. I can’t really vouch for any others out there. But there just ain’t getting around this one. You’ll need something to hold your bike while you work on it.
Many bikes, including older models and track bikes, have bolts attaching the wheels to the frame instead of quick-release levers. If your wheels are bolted on, in most cases you’ll need a 15 mm wrench to remove it. We didn’t test wrenches, because there aren’t that many tiny 15 mm wrenches, but the GearWrench 15mm 12-Point Stubby Combination Wrench is perfect for stuffing into a flat kit and Amazon reviewers seem to think the same. Our experts also recommended the Surly Jethro Tule, but it’s expensive and harder to find.

Next to everything else that might go wrong with a bicycle on an extended ride, a flat is a relatively minor issue that can be easily repaired trailside, if the right tools are at hand. If they aren’t, a quick fix can turn into a long walk. Well-prepared riders will perform a tune-up regularly and clean their bikes after every ride. For the less-diligent, a well-stocked repair kit will suffice.
Basically, you’re stuck with toggling between systems for the advantage of a few pumps, and it doesn’t seem worth it. In the original iteration of this guide, I tested 12 pumps and inflated three different tires completely full to their psi rating, and measured how many pumps it took. Yasuda did similarly for his revamped full-length exploration. That’s 36 tires, and I can guarantee there is no difference between 50 pumps and 100—it’s all terrible.
A bicycle costs anywhere from $250-$9,000 depending what type and quality of bike you want. A utility bike from a department store might cost $300-$500, but experts caution that it will be quite a bit heavier and not as well constructed as other bikes. For a durable, lightweight bike with front-suspension and decent parts, it’s reasonable to pay $750-$1,200. You might be able to pay slightly less, but expect to need some repairs after several months of heavy use.
Nice, helpful, friendly. Central location. Good bikes (I had two over two days.) Bikes had a water bottle cage (some places don't do that!) Provided helmets if needed (I didn't) and a one-sided pannier containing a decently strong but not super-heavy cable lock and a patch kit. Only quibbles: 1) The owner helping me with getting my bikes seemed to 'drop me' for too long when someone else walked in. He should have said to them, after asking what they were in for, that 'I'll be with you as soon as I'm finished with this person.' So I had to wait a little longer than desired, but not bad. 2) On my second day, the pannier bag fell off and got lost after I stopped for lunch, which required locking up the bike somewhere, so I took the bag into restaurant and re-attached it using the two velcro straps on the rear rack. I've used many panniers before, thought I did it correctly. But apparently I did not. So I paid $55 (cost) to replace everything in bag and bag. In hindsight, I wished I'd put a bungee around bag straps to really secure it to bike. PROBABLY MY FAULT. 3) Bring a second lock to lock quick-release front wheel, as decently strong but not super-heavy cable lock isn't long enough for both wheels and frame.I had a second cable lock.
We focused on tools that would be useful to a commuter—someone trying to use a bike as a functional way to get around town, as opposed to riding recreationally (road biking and mountain biking). That said, it’s a wild and wooly bicycling world out there, and the streets are packed with so many different bikes, all shapes and sizes, new and old. Customizing your flat-fixing kit has advantages over buying a preassembled kit that always contains a tool (or two or three) that’s a piece of junk, or you don’t need. Or it’s missing something you do need. If you build your own kit, at least you know everything works. And you can add only what’s necessary for your specific bike without ending up with stuff you don’t need.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.
If you are planning on going on a multi-day ride or just riding a long distance in a day, you should have something for first aid, just in case. Unfortunately, almost everyone who cycles frequently will go down at least once in their life. This kit can be really small and compact and can include bandages, some gauze, and a small bottle of a disinfectant.
On a very sunny Saturday I had a rear spoke break - you can imagine that no shop was willing to promise a quick repair! I was so fortunate to find this shop and will come back - Andy not only told me to come down and he'd get it fixed, he had his assistant work with another couple while he measured, cut to the right size, installed and trued the wheel while I waited! It was awesome, and the whole place had a great feel and good people. Best of all he charged a very fair $20 for all that work - I would have paid a premium for the quick service! After experiencing lots of attitude at other shops and poor service, this was a real find. I hope you will check them out, they have a great selection of bikes and accessories too! Good people and good craftsmanship should be rewarded.

First, I researched. I looked at Amazon’s top-rated products and their user reviews. Then I consulted Bicycling magazine, Gear Junkie, Bike Radar, Outside, and the occasional bit by Lennard Zinn via Velonews. I also found some worthwhile discussions at Bike Forums. Then I spoke with four experts, Ramona Marks, Scott Karoly, Cari Z, and Alison Tetrick, riders from all across the spectrum, who tour, repair, and race.
Owning a bicycle is a good idea, but taking care of it yearns for an experts’ piece of mind. You should not worry too much about taking your bicycle to a mechanic when you can handle the repairing on your own. It will rather save you the cost of every moment you get into a problem. Grab a pick of one of the toolkits from the above review. I assure you that, absolutely no day will you seek a mechanic for service.
The Bicycle Repair Shop is the place to be if you want to buy a new bike, need a repair or to rent a bike. These guy know everything about bikes and then some and at an amazing price. If you need your bike repaired they go above and beyond to help you get your bike repaired. If you are a tourist the shop has a great many bikes to choose from at an excellent price. I visited this shop last time I was in Seattle visiting my son and we rented the tandem bike it was a blast. My son bought a great bike and if he needs a tune up he goes to The Bicycle Repair Shop. This is the best bike shop in all of Seattle !!!!!!!
Broadly speaking there are two major wheel sizes – 700c for road bikes and 26 inch off-road wheels. However there are a whole variety of older, less common wheel sizes and of course fold up bikes have much smaller wheels altogether. Repairing a puncture is not an emergency! It’s a basic procedure that every cyclist should be able to to perform, but doing it correctly involves more steps than many people realise. Wheel building is often seen as the most artful skill in bicycle maintenance, and separates the professionals from the amateurs but that doesn’t mean you should consider it out of reach. Truing a slightly misaligned wheel is a cycle maintenance job that almost any cyclist can perform.
×