```To pick the right size bicycle, you want to measure your height, and specifically your inseam (inside leg), in proportion to the size of the bike frame. The inseam measurement determines the seat height, or the “stack.” Next, you must calculate the “reach,” which is the horizontal distance between the bottom of the frame and the head of the bike -- or, in layman’s terms, the distance between seat and handlebars.
```

If you have just a short time in Seattle there is only one way to see the city. Walk at 2.5 miles an hour? I don't think so. Take buses and trams that you have to wait for and that might not even get you where you need to go? No way Jose. Drive your car? Hahahaha get outta here, don't even talk to me. But what about a BICYCLE??? Now that's the ticket.
These folks took me in right away, diagnosed and fixed my stripped handle bar clamps and had me on my way to work in about 15 minutes. Friendly, straightforward, understands the rider's objectives (in my case, how do I get home from work). Not to mention, the fee was reasonable. I have been in many bike repair places in my 6 decades. This is the best.
The Administration & Event Services office is critical to every thing that happens at the heart of the UCF campus. They are your first stop when planning anything that happens at the Student Union. So whether it's providing logistics for your upcoming event, making room reservations or offering you guidance on proper procedure, the Student Union staff is here to help.
To pick the right size bicycle, you want to measure your height, and specifically your inseam (inside leg), in proportion to the size of the bike frame. The inseam measurement determines the seat height, or the “stack.” Next, you must calculate the “reach,” which is the horizontal distance between the bottom of the frame and the head of the bike -- or, in layman’s terms, the distance between seat and handlebars.
The thumb test is the fine art of pressing on the tube with your thumb to see if it’s inflated. During testing, I took a pressure reading out of curiosity, and to the touch, road tires feel fully inflated around 30 psi. How pathetically sad—30 psi!—when you’re probably trying to reach at least 60 psi on a mountain bike, 70 or more on a hybrid, and it only goes up from there.
Professional mountain biker Rebecca Rusch has been on plenty of long rides and experienced enough mechanical failures to know what makes a fully-stocked repair kit. One of her recent journeys, a 1,200-mile journey through the jungles of Vietnam, Laos and Cambodia along the Ho Chi Minh Trail required the utmost degree of preparedness — “We brought with us a lot of extra bearings, o-rings, stuff that you would never be able to find in Laos and Cambodia. Before I go out on these big adventures, I replace every bearing in my bike, my fork got a total rebuild — everything is in pristine condition,” says Rusch.

It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
I bicycle to and from work to save gas. I don't have a fancy bike, it's just a Schwinn mountain bike that's comfortable and can carry me plus gear but I want to be able to do my own work on it. I needed a book that was simple enough for someone new to bicycle repair and maintenance but could take me through all the upkeep my workhorse needs, and this book does just that. It's well-written and easy to follow.
Modern bottom brackets use a sealed bearing type construction that keeps water and debris locked out, so they seldom go wrong. Maintenance is impossible so they need replacing when they do wear out. Older style cup bottom brackets need to be re-greased every now and again, and occasionally will need to have their bearings replaced. There are a lot more teeth on the chainring cogs than those on the rear cassette, so need changing less regularly. Cranks usually a solid one piece construction so there is not much to go wrong.