This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement.
These guys are awesome.  After work, I got to my bike to discover my back tire was completely flat.  It had a slow leak, so I was able to pump it up enough to make it to their shop.  I got there 10 minutes before closing and they were able to fit me in.  They replaced my tube and picked all of the glass shards out of my tire.  Awesome customer service and they saved me from having to do this myself in the dark and the cold.
If you’re going to use the chain whip you just made, you’ll also need a way to get that cassette off. A lockring remover is a must-have; unless you use one of the shady removal methods I’ve seen on the internet—which I wouldn’t necessarily recommend unless you don’t care much about the condition of the wheel after you use them. I recommend Park Tool’s iterations here that cost about $6, but you’ll need to buy the specific one for your brand/type of cassette. (By the way, I’m assuming you already have an adjustable wrench laying around somewhere to use with this tool. If you don’t, well, you’ll need one of those too.)
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
This gentleman is a true professional!! He is an ex-Marine and I will tell you that he represents them well. He is honest, knowledgeable and extremely reasonable. He repaired my son's bike while I waited and went over the whole bike and made the required adjustments replaced an inner tube and all for 20 dollars!!All the kids in the area pass by and call him by his first name. I will recommend him to everyone I know since there are very little of them out there!!

It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.


We offer a convenient Mobile Bike Shop experience at your home or office. We believe that bicycles can help change the world. Whether you are a road warrior, a commuter, an elite triathlete, a daredevil mountain biker, or enjoy your leisurely weekend rides on your e-bike, our goal is to offer a convenient premium service that gives you more time to do what you love…RIDE!
Unlike floor pumps, most hand pumps do not have pressure gauges. To get readings during my original round of testing for this guide, I built a special rig involving simple hardware-store parts. But the experts I spoke to seem divided on the usefulness of gauges. Half thought they were unnecessary, added bulk, and drove up cost. Why do you need a gauge if you know 100 pumps inflates your tire? But the other half liked them, because the “thumb test” is notoriously inaccurate.
If you own a bike, you need a flat-fixing kit. It’s really that simple. Sure, maybe you’ll get lucky and get a flat close to a shop, or the buses will be running on time for once, but even with all that going for you, getting stranded across town will cost you time, money, and precious sanity. You can put together a great kit in less time than it takes to read this guide.
I own the Lezyne CNC Chain Rod, which I’m a big fan of (yes, I know I’m partial to Lezyne here–they’re a local-to-me, San Luis Obispo company and they sponsored my collegiate team, so I got tons of gear) and it costs right around $30. But the truth is that even the cheapest of chain whips will likely do the job. In fact, I’ve found a dude who knows his stuff and shows you how to make this tool all by yourself. I would even go so far as to say that you probably have enough materials laying about your garage (if not, try your parents’ garage ? ) to put this together without spending anything. Check out the video below:
Many bikes, including older models and track bikes, have bolts attaching the wheels to the frame instead of quick-release levers. If your wheels are bolted on, in most cases you’ll need a 15 mm wrench to remove it. We didn’t test wrenches, because there aren’t that many tiny 15 mm wrenches, but the GearWrench 15mm 12-Point Stubby Combination Wrench is perfect for stuffing into a flat kit and Amazon reviewers seem to think the same. Our experts also recommended the Surly Jethro Tule, but it’s expensive and harder to find.
Mini Pump:   This actually goes on the frame of your bike, as it’s a bit too big for most under-seat bags.   Coming soon, we’ll have a review from Bill of his very favorite one, but a good pump is a lifesaver.    Some people instead carry a CO2 inflator, which is faster and easier to use but does require disposable cartridges, and each time you have a flat, you’ll need at least 2 of those cartridges.  There are combined pump/inflator tools that we’ll also talk about soon.
It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.

Maintenance is the best prevention. “Prevention is the best medicine, and if you’re taking care of your equipment it’s super key. Bikes don’t just fail. If they’re in really good working condition and you clean them at night, and you’re religious about it, bikes are kind of like cars — they’ll start talking to you if something is getting worn or getting creaky or needs to be replaced.”
One key difference, that you can see in the photo, is that the BV uses buckles instead of Velcro on the straps that attach the bag to the underside of the saddle, something much more important than it may seem. A pair of bike shorts (or any shorts) will shred quickly if they’re rubbing against that tiny bit of Velcro protruding from the side of the bag, and it’s sure to destroy expensive sweaters and gym clothes if you stuff the bag into your backpack or messenger bag.
We spent 26 hours on research, videography, and editing, to review the top choices for this wiki. Even recreational riders and commuters ought to conduct regular maintenance to ensure safe and proper functioning of their cycle, so you really don't have to be a professional to invest in one of these comprehensive bike repair kits. Our selections included options that cover the basics along with a few that include all the tools you're ever likely to need. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best bike repair kit on Amazon.
Bike Radar gives the Pedro’s levers 4.55 out of five stars and claims they’re the “best out there.” (Can we pause to admire the extra five hundredths of a star the site chose to award it? Very specific.) Aaron Gulley, writing for Outside, states, “I can’t count the number of times I’ve snapped cheap plastic sticks, shredded my hand in the process, stomped around cursing in pain for 10 minutes, and then, insult to injury, been tool-less and unable to get my tire off anyway. That will never happen with Pedro’s.”
Next, two-stage designs. There are two types of hand pump. HV (high-volume) pumps, ones that pump a lot of air but don’t have a lot of pressure, which are used for mountain bikes. The Lezyne Alloy Drive is a high-volume pump. Then there are HP (high-pressure) pumps, which pump a small amount of air but can inflate to very high pressures and are used on road bikes. Our top pick is a high-pressure pump.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
3D Printers Baby Bath Tub Baby Strollers Bar Stool Bean Bag Chair best actor Bike cover Blackhead Remover Boys' Boxer Underwear Car Chargers Ceiling Fans Chair Cushions cleaner Dining Chair Diving Masks Elbow Braces Electric Air Fryer Electric Stove Fizik Saddles Folding Ladders gas cooktop Handheld CB Radio inflatable boat Kindle Paperwhite Makeup Brush Makeup Chairs Men's Cycling Shoes Paper Towel Holder Ping Pong Paddles pool cue rack Preqnancy body pillow Projector Stands RC Helicopter robot rocking horse Seagrass Rug Small Indoor Dog House sound bars Table Round toddler travel bed vacuum Vanity Makeup Mirrors Walmart Folding Table Women's Condoms Wood Table Lamps
Maintenance is the best prevention. “Prevention is the best medicine, and if you’re taking care of your equipment it’s super key. Bikes don’t just fail. If they’re in really good working condition and you clean them at night, and you’re religious about it, bikes are kind of like cars — they’ll start talking to you if something is getting worn or getting creaky or needs to be replaced.”

These are some great ideas, especially the simple ones like bringing a garbage bag. That’s something so easy and cheap that it’s easy to forget entirely, but as you say, it can make a huge difference in the right circumstances. It’s also good that you discuss some minor bike repairs. That’s another thing that can salvage or destroy your ride. You want to be as prepared as possible for the best possible experience.
Writer Peter Flax, the former editor-in-chief of Bicycling magazine, rode over 1,000 miles and tested 15 tools for our full-length guide to multi-tools, and he concluded the Topeak Mini 9 is the best for casual cyclists. It’s tiny, it’s light, it’s easier to get some leverage with than other tools that have different designs. It’s not meant for serious wrenching on your bike, but it’s good for on-the-fly adjustments.

Create emergency patches on tires or tubes with this Bike Tire Repair Kit. Each pack comes with everything you need to fix a flat, including a spokes wrench. When you find a puncture or nail hole in your riding essential, grab an application from this bicycle repair kit to hold in enough air so you can continue on your way until a replacement tire can be located. It includes adhesives and patches of different sizes for your convenience. Made of steel, the bicycle tire repair kit is durable and long-lasting. Keep the set with you at all times while riding your bicycle so that you have it in the event of an emergency. The size of the kit makes it easy to carry in a backpack or zippered cargo bag. Cover different sizes and types of holes and tears that make riding difficult with this Bike Tire Repair Kit.


Basically, you’re stuck with toggling between systems for the advantage of a few pumps, and it doesn’t seem worth it. In the original iteration of this guide, I tested 12 pumps and inflated three different tires completely full to their psi rating, and measured how many pumps it took. Yasuda did similarly for his revamped full-length exploration. That’s 36 tires, and I can guarantee there is no difference between 50 pumps and 100—it’s all terrible.
Don’t rely on others. “People need to recognize that now there are different cassette sizes, so there are different chains depending on what gear you have. A lot of people are like, ‘Oh my friend is always prepared they always have the stuff, I’m not going to bring anything.’ All of the stuff now is very bike-specific, and you have to have your own package of stuff.”
Many bikes, including older models and track bikes, have bolts attaching the wheels to the frame instead of quick-release levers. If your wheels are bolted on, in most cases you’ll need a 15 mm wrench to remove it. We didn’t test wrenches, because there aren’t that many tiny 15 mm wrenches, but the GearWrench 15mm 12-Point Stubby Combination Wrench is perfect for stuffing into a flat kit and Amazon reviewers seem to think the same. Our experts also recommended the Surly Jethro Tule, but it’s expensive and harder to find.

The Bicycle Repair Shop does rentals by the hour or by the day. They have reasonable rates. They have solid, lightweight hybrid bikes so you can tackle train tracks and brick streets and hills. They also have road bikes for the more experienced. You can reserve online in advance. You get a helmet and a lock with your rental. The staff in the shop are friendly and will suggest routes and point out hills if you're new to the area. And believe me these hills are no joke!


Owning a bicycle is a good idea, but taking care of it yearns for an experts’ piece of mind. You should not worry too much about taking your bicycle to a mechanic when you can handle the repairing on your own. It will rather save you the cost of every moment you get into a problem. Grab a pick of one of the toolkits from the above review. I assure you that, absolutely no day will you seek a mechanic for service.
Over the years, I’ve come across plenty of articles that claim to tell you how to build up your cycling toolkit for cheap. Somehow the word “cheap” stops recurring in the long list of “essential” bike repair bits and pieces. The truth is, there is no real way to build a whole shop of tools all at once without plopping down a few hundred bucks. But in an attempt to show everyone that not all of us truly need a full complement of bike tools, I present the truest, most budget-conscious, and barest of bones options to you.
All multi-tools are not created equal, but most with a plethora of features will get plenty of the jobs done. I personally like, and use often, the Lezyne RAP-21 LED tool, which will run you around $30. I like it because not only is it a high quality construction, but it has just about everything you’ll need, plus a sweet mini light. This will give you a chain breaker, spoke wrench, disc brake wedge, and all the most often used Allen keys and drivers. We’re talking a decent number of tools for 1/4 of what they would cost buying them separately.
Don't ever be stranded without the right tools or know-how. The Super Hero Kit for Road Biking is designed to empower all levels of cyclists to fix mechanical problems that can arise on any ride, and to get back home safely. An innovative, time-saving, and economical combination of high-quality tools and materials, and detailed instruction manual, as well as a tube, pump, and bike bag - it's an all-in-one solution - that's ready for your next ride.
Mini Pump:   This actually goes on the frame of your bike, as it’s a bit too big for most under-seat bags.   Coming soon, we’ll have a review from Bill of his very favorite one, but a good pump is a lifesaver.    Some people instead carry a CO2 inflator, which is faster and easier to use but does require disposable cartridges, and each time you have a flat, you’ll need at least 2 of those cartridges.  There are combined pump/inflator tools that we’ll also talk about soon.

Bikes have remained popular since time in memorial. It’s fun being a rider. Their existence brings about the need to preserve their smooth riding. A bicycle like any mechanically driven tool requires regular service as they are prone to artificial failure. To ensure an outstanding service, the appropriate toolkit should be employed. It may not be easy to obtain the best toolkit, but with us, you are guaranteed quality and efficient toolkits.

Dennis Bailey has been actively involved in bike repair and maintenance for almost two decades. He has worked on bikes on bike tours in the United States, Europe, and Latin America. Keith Gates has been repairing bikes for more than 30 years and provides personalized service as the owner of A-1 Cycling, with locations in Manassas and Herndon, Virginia.
×