Many bikes, including older models and track bikes, have bolts attaching the wheels to the frame instead of quick-release levers. If your wheels are bolted on, in most cases you’ll need a 15 mm wrench to remove it. We didn’t test wrenches, because there aren’t that many tiny 15 mm wrenches, but the GearWrench 15mm 12-Point Stubby Combination Wrench is perfect for stuffing into a flat kit and Amazon reviewers seem to think the same. Our experts also recommended the Surly Jethro Tule, but it’s expensive and harder to find.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
One key difference, that you can see in the photo, is that the BV uses buckles instead of Velcro on the straps that attach the bag to the underside of the saddle, something much more important than it may seem. A pair of bike shorts (or any shorts) will shred quickly if they’re rubbing against that tiny bit of Velcro protruding from the side of the bag, and it’s sure to destroy expensive sweaters and gym clothes if you stuff the bag into your backpack or messenger bag.
The thumb test is the fine art of pressing on the tube with your thumb to see if it’s inflated. During testing, I took a pressure reading out of curiosity, and to the touch, road tires feel fully inflated around 30 psi. How pathetically sad—30 psi!—when you’re probably trying to reach at least 60 psi on a mountain bike, 70 or more on a hybrid, and it only goes up from there.
There are two major types of headset- older, threaded headsets that have a quill that drops into the stem of the fork creating an interference connection, and newer threadless headsets that the stem is bolted and clamped on to. Flat handle bars are preferred by off road cyclists who can ride in a more upright postion whilst still having the controls at their fingertips, whereas drop handlebars offer more cycling positions and are favoured by road cyclists who typically spend more time in the saddle. The controls attached to the different styles of bar are operated and maintained in different ways.
If you are planning on going on a multi-day ride or just riding a long distance in a day, you should have something for first aid, just in case. Unfortunately, almost everyone who cycles frequently will go down at least once in their life. This kit can be really small and compact and can include bandages, some gauze, and a small bottle of a disinfectant.
Change and a $20 bill: In case your cell phone’s battery dies, it’s nice to still be able to use a payphone if you need to. Also, the $20 is a great thing to have in case you lose your wallet or have some other mishap. I’d rather be able to sit in a coffee shop or fast food restaurant when it starts raining while I’m waiting for my friend or cab ride, and a hot cup of tea or coffee or the beverage of your choice and a snack makes it all the more pleasant. Just try to remember, this is for emergencies, and if you use it, replace it ASAP!
If you have just a short time in Seattle there is only one way to see the city. Walk at 2.5 miles an hour? I don't think so. Take buses and trams that you have to wait for and that might not even get you where you need to go? No way Jose. Drive your car? Hahahaha get outta here, don't even talk to me. But what about a BICYCLE??? Now that's the ticket.
I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
Now you might be wondering: “I’m carrying a tube; why carry patches at all?” As insurance for the unforeseeable. Wirecutter senior editor Christine Ryan admits she didn’t use to pack them, but said, “I’ve regretted that decision when I’ve had a flat on a ride, used my spare tube, and then, half an hour later, had a second flat. Also, lots of people aren’t very good at figuring out—or don’t take the time to figure out—what caused their flat and remove the cause: thorn, eensy bit of glass, whatever. Then they promptly have a second flat, and everyone else laughs at them.”
There are patches that don’t require vulcanizer—the infamous peel-and-stick. One brand, the Park Tool GP-2, has some genuinely enthusiastic endorsements, so we tested it. I applied Park Tool patches to four different tires, at three different psi levels (60, 90, and 120). Three of the four didn’t hold—two released within minutes. The fourth deflated overnight. I redid the test, but repeated a second time, they all leaked within a day.
Do not take your Bike to Kyle's Bike Shop they handled my bike so poorly they can not work on Vintage Schwinn' and the attitude they had if it wasn't a high dollar bike don't expect good service. I had to find my own parts, had to take the bike back twice to get the wheel trued and they ruined my bike it is so scrapped up the Schwinn is gone on the side of the bike. If you care about your bike do not take it here.
As you mentioned, it is surprising how often you can get multiple flat tires on while riding, particularly on longer sprints. The tip about bringing a patch kit in your bike repair kit can be incredibly helpful if you’ve already had one flat tire. I agree that all you listed seems like an awful lot to carry, but it’s always better to be safe than sorry, isn’t it?
Before I get started, I should mention that I never leave reviews. This is probably my first one on Yelp. These guys are just so great that I felt compelled to give them a shoutout. This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement. These guys will give you their best and provide some laughs as well. Couldn't recommend them more!
Over the years, I’ve come across plenty of articles that claim to tell you how to build up your cycling toolkit for cheap. Somehow the word “cheap” stops recurring in the long list of “essential” bike repair bits and pieces. The truth is, there is no real way to build a whole shop of tools all at once without plopping down a few hundred bucks. But in an attempt to show everyone that not all of us truly need a full complement of bike tools, I present the truest, most budget-conscious, and barest of bones options to you.
It’s both surprising, and not, if you think about it. The way I’ve usually seen it happen is first the rear tire goes flat, then the front one. My theory is that both tires went through the same pile of glass/thorns/metal bits and they both picked up junk. the reason for the flat occurring on the back first is because there’s more weight on that tire, so the offending article works its way through the tread more quickly.