This is the shop I hoped to find when I began commuting two years ago. I'm a daily commuter and I love knowing that these guys will help me almost anytime that I need it. Andy, Jake and Brad listen and make sure to help me as best they can and are always speedy about it. Additionally, they encourage me to do my own work on my bikes when I have the time/when they know I'm capable and I really appreciate that encouragement.
It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
A good patch will stick to your tube enough to keep air from leaking out. A great patch will act like a second skin and actually strengthen the tube where it’s applied, flexing and stretching with the tire. After 36 hours of testing, our official endorsement goes to the Rema TT 02 Touring Repair Kit. Its patches do everything other patches do, just better. The edge of the patch is also ruffled, which provides more edge surface area to bond—that’s a good thing.
Return: Bicycle and lock must be returned by the end of the loan period. User will be charged a $10.00/day late fee. After 10 business days user will be charged the full cost of the bicycle ($350) and rented equipment ($50 for lock and/or key). Failure to return bicycle, helmet and lock will subject user to legal liability of $400.00, as well as having student account placed on hold.
The Pedro’s lever slipped only once throughout testing, though that may have been my fault because I was spaced out after changing 16 different tires. So they’re not foolproof, but they are far and away more reliable than the next closest competitor, from Park Tool, because the small, rounded tip on that one is hard to keep seated under the tire. Not impossible, but I wouldn’t choose it over Pedro’s.
Riding the bus with three infants in a stroller is no easy task, especially when you realize you have a flat tire as soon as you step foot on the pavement of 2nd and University. Luckily, I found The Bicycle Repair Shop. Andy happily filled my tire with air, and when it was flat again an hour later, found a replacement tube in minutes. He changed the tire with the babies still in the stroller! This was such an amazing experience that totally made a fun day possible for us! Thank you, Andy!
Bikes have remained popular since time in memorial. It’s fun being a rider. Their existence brings about the need to preserve their smooth riding. A bicycle like any mechanically driven tool requires regular service as they are prone to artificial failure. To ensure an outstanding service, the appropriate toolkit should be employed. It may not be easy to obtain the best toolkit, but with us, you are guaranteed quality and efficient toolkits.
But before I get started, let me share with you a few tips. OK, one tip: Get a work stand. Because putting your bike upside down isn’t good for it—yes, I said it. When I first started fixing my own bikes, I couldn’t afford a fancy $300, folding, magnetic, fixes-the-bike-for-you stand. I tried piecing together a “DIY $30 Stand.” I followed all the directions that the Internet demanded, and once I’d bought all the clamps and pipes, this thing cost really more in the neighborhood of $60—but it only stayed upright with a rope tied to something sturdy in the garage. It was one word: junk. So I bit the veritable chainring and charged a decent stand on my credit card (I hate debt, folks).
Brakes come in a variety of designs depending on the age and style of your bike. Rim brakes offer more modulation but have less stopping power, so are more suited to riding on the roads. Disc brakes can provide huge amounts of stopping power so are best suited to off road riding, although ‘V’ rim brakes are also well suited to mountain biking. All brakes use a friction system to stop the movement of the wheel, so regular checks of the contact pads should form part of your regular cycle maintenance.