I got some problems with my gears and I was wondering how to fix it, then got the idea on the internet about KELLY'S,I decided to go with them to fix the errors, that was my first time and was a great experience,they are all very accurate with their profession,very friendly,very polite and very honest as well,they just took half an hour to make me free.so,with the first experience I have become the fan of Kyle's.definitely suggested to everyone.
Pedals are important because the serve as the contact point between the rider and the bike’s transmission. Clip-less pedals systems come in a variety of designs favoured by individual manufacturers, but the mechanics of all styles are roughly the same. Tiny adjustments in the position of the show cleat – that snaps into position on the pedal – can make a big difference to the comfort and health of the rider.
These guys are awesome.  After work, I got to my bike to discover my back tire was completely flat.  It had a slow leak, so I was able to pump it up enough to make it to their shop.  I got there 10 minutes before closing and they were able to fit me in.  They replaced my tube and picked all of the glass shards out of my tire.  Awesome customer service and they saved me from having to do this myself in the dark and the cold.
As you mentioned, it is surprising how often you can get multiple flat tires on while riding, particularly on longer sprints. The tip about bringing a patch kit in your bike repair kit can be incredibly helpful if you’ve already had one flat tire. I agree that all you listed seems like an awful lot to carry, but it’s always better to be safe than sorry, isn’t it?
Next to everything else that might go wrong with a bicycle on an extended ride, a flat is a relatively minor issue that can be easily repaired trailside, if the right tools are at hand. If they aren’t, a quick fix can turn into a long walk. Well-prepared riders will perform a tune-up regularly and clean their bikes after every ride. For the less-diligent, a well-stocked repair kit will suffice.
Let me go ahead and get the bad stuff out of the way. First of all, this stand is NOT the same level of quality as something you would find in a bicycle shop being used for the shop's repairs. it's quite a bit more flimsy, and the grip likes to rotate if you don't get the bike's center of gravity just right. The tool tray is also made out of a rather cheap plastic that can break easily at the rim. That being said, this stand is perfect for home users and makes mundane tasks like fixing a flat or cleaning the chain much easier. It easily holds my Raleigh Merit 3, and I don't worry about the thing falling even if the grip tilts a bit. The stand significantly shortened the time I needed to change an inner tube on my bicycle, and made me less worried about damaging something on the bike by jury-rigging a stand out of whatever I had lying around.
A pair of disposable latex gloves:  Not absolutely necessary, but good for keeping grease and grime off your hands during a repair.  Also, nice to have in an emergency when it starts raining and the temperature drops 20 degrees and you don’t have a pair of regular gloves.   Just keeping your hands dry and the wind from directly blowing on them makes a huge difference in comfort.
A pair of disposable latex gloves:  Not absolutely necessary, but good for keeping grease and grime off your hands during a repair.  Also, nice to have in an emergency when it starts raining and the temperature drops 20 degrees and you don’t have a pair of regular gloves.   Just keeping your hands dry and the wind from directly blowing on them makes a huge difference in comfort.

A wrench that fits the hub nuts:   If your bike has quick release front and rear wheels, you don’t need this, but if you have an internal hub on the back, such as the NuVinci, a wrench that fits is a great idea.  99% of the time, this is a 15mm wrench, but you should check your bike.   A 6 inch adjustable wrench can also work, but it will be heavier, and when using an adjustable wrench, you do need to take more care to not round over the nuts.   A fixed wrench is the best choice.    Some multi-tools have a 15 mm wrench built in, but again, if you have limited hand strength, something with more leverage is a great idea.


It is a good solid stand made mostly from heavy metal, but it does have a couple of problems. (I will use part names from the instructions to explain.) First, the clamp between the "telescopic bar" and the "upright" is plastic. It arrived broken in the box. Whoever boxed it should understand that if you put it in the box broken, the customer will remove it from the box broken. I did not return it as broken because I was able to Gorilla Glue it back together and it works fine; it clamps tight enough to hold the telescopic bar in place. Second, the "bike support stand" (the horizontal bar at the top that holds the bike), when attached to the seat support does not grip tight enough to hold the bike in the position I set because there is too much weight from the front of the bike. The torque causes the bike to rotate until the front wheel is on the ground. That is not enough for me to return the stand because I seldom work on the front wheel and if I do I can attach the stand to the top horizontal of the bike frame. I think they could fix the problem by not making the "bike support stand" so smooth, give that part a sandpaper like finish or put rubber fingers inside the clamp so the part does not slip under the torque from the weight of the front of the bike. I might rough up the stand part with sandpaper, or put small grooves in it to give the clamp something to grip on to see if that solves the problem. Third, the clamp holding the bike frame even at full tight will not keep the bike from rotating around the frame. It is not enough for me to send the stand back, just a minor annoyance. The problem is there is smooth plastic trying to clamp a smooth metal frame. I think they could fix this by putting thin rubber pads in the clamp. I will probably run out and get some pads to try that out. I think it is a good stand for the price. The stand itself is made from much heavier metal than I expected. It is very stable with the four legs. I easily overcame all the issues so I kept it.
First, I researched. I looked at Amazon’s top-rated products and their user reviews. Then I consulted Bicycling magazine, Gear Junkie, Bike Radar, Outside, and the occasional bit by Lennard Zinn via Velonews. I also found some worthwhile discussions at Bike Forums. Then I spoke with four experts, Ramona Marks, Scott Karoly, Cari Z, and Alison Tetrick, riders from all across the spectrum, who tour, repair, and race.
Road riders need lightweight, tiny tools that can fit into jersey pockets. A lot of those items are made of carbon fiber, which is lighter than aluminum. Other iconic trappings of road riding, like CO2 cartridges and spandex outfits, are also geared toward minimalism, but all of that downsizing comes at a cost. Commuters don’t have to be as concerned with weight, so unless you covet something specific, don’t spend the extra money.
Brakes come in a variety of designs depending on the age and style of your bike. Rim brakes offer more modulation but have less stopping power, so are more suited to riding on the roads. Disc brakes can provide huge amounts of stopping power so are best suited to off road riding, although ‘V’ rim brakes are also well suited to mountain biking. All brakes use a friction system to stop the movement of the wheel, so regular checks of the contact pads should form part of your regular cycle maintenance.
×